HA5351_14 Datasheet, PDF (2/7 Pages) Intersil Corporation – 64ns Sample and Hold Amplifier

HA5351
Absolute Maximum Ratings
Voltage Between V+ and V- Terminals. . . . . . . . . . . . . . . . . . . .+11V
Differential Input Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6V
Voltage Between Sample and Hold Control and Ground. . . . . +5.5V
Output Current, Continuous . . . . . . . . . . . . . . . . . . . . . . . . . . ±37mA
Operating Conditions
Temperature Range . . . . . . . . . . . . . . . . . . . . . . . . . .-40°C to +85°C
Thermal Information
Thermal Resistance (Typical, Note 1)
θ_JA (°C/W)
SOIC Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
160
Maximum Junction Temperature (Plastic Package) . . . . . . . +150°C
Maximum Storage Temperature Range . . . . . . . . . -65°C to +150°C
Pb-Free Reflow Profilesee link below
http://www.intersil.com/pbfree/Pb-FreeReflow.asp
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the
device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
NOTE:
1. θ_JA is measured with the component mounted on an evaluation PC board in free air.
Electrical Specifications
Test Conditions: V_SUPPLY = ±5V; C_H = Internal = 15pF, Digital Input: V_IL = 0V (Sample), V_IH = 4.0V (Hold).
Non-Inverting Unity Gain Configuration (Output Tied to -Input), C_L = 5pF,
Unless Otherwise Specified
PARAMETER
TEST CONDITIONS
TEMP.
(°C)
MIN
TYP
MAX
UNITS
INPUT CHARACTERISTICS
Input Voltage Range
Full
-2.5
-
+2.5
V
Input Resistance (Note 2)
+25
100
500
-
kΩ
Input Capacitance
+25
-
-
5
pF
Input Offset Voltage
+25
-2
-
2
mV
Full
-3.0
-
3.0
mV
Offset Voltage Temperature Coefficient
Full
-
15
-
µV/°C
Bias Current
Full
-
2.5
5
µA
Offset Current
Full
-1.5
-
+1.5
µA
Common Mode Range
Full
-2.5
-
+2.5
V
Common Mode Rejection Ratio
±2.5V, Note 3
Full
60
80
-
dB
TRANSFER CHARACTERISTICS
Large Signal Voltage Gain
V_OUT = ±2.5V
+25
95
108
-
dB
Full
85
-
-
dB
Unity Gain -3dB Bandwidth
25
-
40
-
MHz
TRANSIENT RESPONSE
Rise Time
200mV Step
+25
-
8.5
-
ns
Overshoot
200mV Step
+25
0
-
30
%
Slew Rate
5V Step
Full
88
105
-
V/µs
DIGITAL INPUT CHARACTERISTICS
Input Voltage
V_IH
+25, +85
2.1
-
5.0
V
-40
2.4
-
5.0
V
Input Current
OUTPUT CHARACTERISTICS
V_IL
V_IL = 0V
V_IH = 5V
Full
0
-
0.8
V
Full
-1.0
-
1.0
µA
Full
-1.0
-
1.0
µA
Output Voltage
Output Current
R_L = 510Ω
R_L = 100Ω
Full
-3.0
-
+3.0
V
+25, +85
20
25
-
mA
-40
15
-
-
mA
Full Power Bandwidth
Output Resistance
5V_P-P, A_V = +1, -3dB
Hold Mode
Full
-
13
-
MHz
+25
-
0.02
-
Ω
Total Output Noise
(DC to 10MHz)
Sample Mode
Hold Mode
+25
-
325
-
µV_RMS
+25
-
325
-
µV_RMS
2
FN3690.11
April 25, 2013