HA5023_06 Datasheet, PDF (2/16 Pages) Intersil Corporation – Dual 125MHz Video Current Feedback Amplifier

HA5023
Absolute Maximum Ratings
Voltage Between V+ and V- Terminals. . . . . . . . . . . . . . . . . . . . .36V
DC Input Voltage (Note 3) . . . . . . . . . . . . . . . . . . . . . . . . ±V_SUPPLY
Differential Input Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10V
Output Current (Note 4) . . . . . . . . . . . . . . . . . Short Circuit Protected
ESD Rating (Note 3)
Human Body Model (Per MIL-STD-883 Method 3015.7). . . 2000V
Operating Conditions
Temperature Range . . . . . . . . . . . . . . . . . . . . . . . . . . .-40°C to 85°C
Supply Voltage Range (Typical). . . . . . . . . . . . . . . . . ±4.5V to ±15V
Thermal Information
Thermal Resistance (Typical, Note 2)
θ_JA (°C/W)
PDIP Package* . . . . . . . . . . . . . . . . . . . . . . . . . . . .
130
SOIC Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
160
Maximum Junction Temperature (Note 1) . . . . . . . . . . . . . . . . . 175°C
Maximum Junction Temperature (Plastic Package, Note 1) . . 150°C
Maximum Storage Temperature Range . . . . . . . . . . -65°C to 150°C
Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . 300°C
(SOIC - Lead Tips Only)
*Pb-free PDIPs can be used for through hole wave solder process-
ing only. They are not intended for use in Reflow solder processing
applications.
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the
device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
NOTES:
1. Maximum power dissipation, including output load, must be designed to maintain junction temperature below 175°C for die, and below 150°C
for plastic packages. See Application Information section for safe operating area information.
2. θ_JA is measured with the component mounted on an evaluation PC board in free air.
3. The non-inverting input of unused amplifiers must be connected to GND.
4. Output is protected for short circuits to ground. Brief short circuits to ground will not degrade reliability, however, continuous (100% duty cycle)
output current should not exceed 15mA for maximum reliability.
Electrical Specifications
PARAMETER
V_SUPPLY = ±5V, R_F = 1kΩ, A_V = +1, R_L = 400Ω, C_L ≤ 10pF, Unless Otherwise Specified
TEST CONDITIONS
(NOTE 9)
TEST TEMP.
LEVEL
(°C) MIN
TYP
MAX
INPUT CHARACTERISTICS
Input Offset Voltage (V_IO)
A
25
-
0.8
3
A
Full
-
-
5
Delta V_IO Between Channels
Average Input Offset Voltage Drift
A
Full
-
1.2
3.5
B
Full
-
5
-
V_IO Common Mode Rejection Ratio
Note 5
A
25
53
-
-
A
Full
50
-
-
V_IO Power Supply Rejection Ratio
±3.5V ≤ V_S ≤ ±6.5V
A
25
60
-
-
A
Full
55
-
-
Input Common Mode Range
Note 5
A
Full ±2.5
-
-
Non-Inverting Input (+IN) Current
A
25
-
3
8
A
Full
-
-
20
+IN Common Mode Rejection
(+I_BCMR
=
1
+R_IN
)
+IN Power Supply Rejection
Note 5
±3.5V ≤ V_S ≤ ±6.5V
A
25
-
-
0.15
A
Full
-
-
0.5
A
25
-
-
0.1
A
Full
-
-
0.3
Inverting Input (-IN) Current
A
25, 85
-
4
12
A
-40
-
10
30
Delta -IN BIAS Current Between Channels
A
25, 85
-
6
15
A
-40
-
10
30
UNITS
mV
mV
mV
µV/°C
dB
dB
dB
dB
V
µA
µA
µA/V
µA/V
µA/V
µA/V
µA
µA
µA
µA
2
FN3393.8
June 2, 2006