EL2228_07 Datasheet, PDF (2/12 Pages) Intersil Corporation – Dual Low Noise Amplifier

EL2228
Absolute Maximum Ratings (T_A = +25°C)
Supply Voltage between V_S+ and V_S- . . . . . . . . . . . . . . . . . . . .+28V
Input Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . V_S- - 0.3V, V_S +0.3V
Maximum Continuous Output Current . . . . . . . . . . . . . . . . . . . 40mA
ESD Voltage. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2kV
Thermal Information
Maximum Die Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . +150°C
Storage Temperature . . . . . . . . . . . . . . . . . . . . . . . .-65°C to +150°C
Power Dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . See Curves
Operating Temperature . . . . . . . . . . . . . . . . . . . . . . .-40°C to +85°C
Pb-free reflow profile . . . . . . . . . . . . . . . . . . . . . . . . . .see link below
http://www.intersil.com/pbfree/Pb-FreeReflow.asp
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the
device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
NOTE: All parameters having Min/Max specifications are guaranteed. Typ values are for information purposes only. Unless otherwise noted, all tests are at the specified
temperature and are pulsed tests, therefore: T_J = T_C = T_A
Electrical Specifications V_S+ = +12V, V_S- = -12V, R_L = 500Ω and C_L = 3pF to 0V, R_F = 420Ω and T_A = +25°C Unless Otherwise
Specified.
PARAMETER
DESCRIPTION
CONDITIONS
MIN TYP MAX UNIT
INPUT CHARACTERISTICS
V_OS
TCV_OS
I_B
R_IN
C_IN
CMIR
Input Offset Voltage
Average Offset Voltage Drift
Input Bias Current
Input Impedance
Input Capacitance
Common-Mode Input Range
V_CM = 0V
Measured over operating temperature range
0.2
3
mV
-4
µV/°C
V_CM = 0V
-9
-4.5
-1
µA
8
MΩ
1
pF
-11.8
+10.4
V
CMRR
Common-Mode Rejection Ratio
A_VOL
Open-Loop Gain
e_N
Voltage Noise
i_N
Current Noise
OUTPUT CHARACTERISTICS
for V_IN from -11.8V to +10.4V
for V_IN from -10V to +10V
-5V ≤ V_OUT ≤ 5V
f = 100kHz
f = 100kHz
60
90
60
75
60
75
4.9
1.2
dB
dB
dB
nV/√Hz
pA/√Hz
V_OL
Output Swing Low
V_OH
Output Swing High
I_SC
Short Circuit Current
POWER SUPPLY PERFORMANCE
R_L = 500Ω
R_L = 250Ω
R_L = 500Ω
R_L = 250Ω
R_L = 10Ω
-10.3 -10
V
-9.5
-9
V
10
10.3
V
9.5
10
V
140
180
mA
PSRR
Power Supply Rejection Ratio
I_S
Supply Current (per Amplifier)
DYNAMIC PERFORMANCE
V_S is moved from ±10.8V to ±13.2V
No load
65
83
4
5
dB
6
mA
SR
Slew Rate (Note 1)
±2.5V square wave, measured 25% to 75% 44
65
V/µs
t_S
Settling to +0.1% (A_V = +1)
BW
-3dB Bandwidth
(A_V = +1), V_O = 2V step
50
ns
80
MHz
HD2
2nd Harmonic Distortion
HD3
3rd Harmonic Distortion
NOTE:
1. Slew rate is measured on rising and falling edges
f = 1MHz, V_O = 2V_P-P, R_L = 500Ω, A_V = 2
f = 1MHz, V_O = 2V_P-P, R_L = 150Ω, A_V = 2
f = 1MHz, V_O = 2V_P-P, R_L = 500Ω, A_V = 2
f = 1MHz, V_O = 2V_P-P, R_L = 150Ω, A_V = 2
-86
dBc
-79
dBc
-93
dBc
-70
dBc
2
FN7008.2
May 3, 2007