ISL54206A Datasheet, PDF (17/19 Pages) Intersil Corporation – MP3/USB 2.0 High Speed Switch with Negative Signal Handling

ISL54206A
Revision History
The revision history provided is for informational purposes only and is believed to be accurate, but not warranted. Please go to
web to make sure you have the latest Rev.
DATE REVISION
CHANGE
09/24/2010 FN6515.2 Added section titled “USB Switch Cell Off-Isolation” to page 10.
06/15/2010
FN6515.1
On page 1:
Added "The L and R 50kΩ resistors to ground are not shown." to “Application Block Diagram”. Removed
(2) 50kΩ resistors, which were tied to L and R next to "CODEC" block
Updated Pb-free bullet in “Features”
On page 2:
Added PD to “Pin Descriptions” table
Updated Pb-free notes in “Ordering Information” per new verbiage based on lead finish. Added TB347
link to ordering information for reel specifications.
On page 4:
Added Latch up to Abs Max Ratings
Added Theta JC to “Thermal Information”. Changed 10 Ld µTQFN Theta JA from 130 to 145. Changed
10 Ld TDFN Theta JA from 110 to 55. Added applicable Theta JC notes.
Added standard over temp note to common conditions of spec table (Boldface limits apply..)
On page 5:
Changed “ON Leakage Current, I_Dx” room temp and full temp limits from:
Room temp MIN/TYP/MAX: from -10/2/10nA to -30/8/30nA
Full temp MIN/MAX: from -75/75nA to -300/300nA
On page 6:
Changed “Positive Supply Current, IDD (Low Power State)” room temp and full temp limits from:
Room temp TYP/MAX: from 1/7nA to 4/25nA
Full temp: removed MAX of 140nA. Added TYP of 150nA
On page 4 to page 6:
Updated standard over-temp Note 15 in MIN/MAX columns of the Electrical Specifications table.
On page 18:
Updated POD L10.2.1X1.6A to most recent revision. Changes were:
Convert to new format by moving dimensions from table onto drawing
Corrected leadframe thickness in Detail x from 0.2 REF to 0.125 REF
Corrected Note 4 to read "...between 0.15mm and 0.30mm...", it previously read "...between .015mm
and 0.30mm..."
Corrected the word "indentifier" in Note 8 to read "identifier".
On page 19:
Updated POD L10.3x3A to most recent revision. Changes were to add Typical Recommended Land
Pattern & convert to new format by moving dimensions from table onto drawing (no dimension
changes)
06/25/2007 FN6515.0 Initial Release.
Products
Intersil Corporation is a leader in the design and manufacture of high-performance analog semiconductors. The
Company's products address some of the industry's fastest growing markets, such as, flat panel displays, cell phones,
handheld products, and notebooks. Intersil's product families address power management and analog signal
processing functions. Go to www.intersil.com/products for a complete list of Intersil product families.
*For a complete listing of Applications, Related Documentation and Related Parts, please see the respective device
information page on intersil.com: ISL54206A
To report errors or suggestions for this datasheet, please go to www.intersil.com/askourstaff
FITs are available from our website at http://rel.intersil.com/reports/search.php
For additional products, see www.intersil.com/product_tree
Intersil products are manufactured, assembled and tested utilizing ISO9000 quality systems as noted
in the quality certifications found at www.intersil.com/design/quality
Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications
at any time without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by
Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any
infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any
patent or patent rights of Intersil or its subsidiaries.
For information regarding Intersil Corporation and its products, see www.intersil.com
17
FN6515.2
September 30, 2010