HA-5101883 Datasheet, PDF (16/16 Pages) Intersil Corporation – Low Noise, High Performance Operational Amplifier

HA-5101
TABLE 1. TYPICAL PERFORMANCE CHARACTERISTICS
Device Characterized At: V_S = ±15V, R_L = 2kΩ, C_L = 50pF, A_VCL = +1V/V, Unless Otherwise Specified
PARAMETER
TEST CONDITIONS
TEMP (°C)
TYP DESIGN LIMITS
UNITS
Offset Voltage
Offset Voltage Average Drift
V_CM = 0V
Versus Temperature
+25
0.8
-55 to +125
3
Table 1
7
mV
µV/°C
Offset Current Average Drift
Versus Temperature
-55 to +125
100
250
pA/°C
Input Bias Current
Input Offset Current
Differential Input Resistance
Input Noise Voltage Density
Input Noise Current Density
Large Signal Voltage Gain
V_CM = 0V
V_CM = 0V
V_CM = 0V
f_o = 10Hz
f_o = 100Hz
f_o = 1kHz
f_o = 10Hz
f_o = 100Hz
f_o = 1kHz
V_OUT = ±10V
+25
65
Table 1
nA
+25
35
Table 1
nA
+25
500
Table 3
kΩ
+25
5.4
9
nV/√Hz
+25
3.4
5.5
nV/√Hz
+25
3.2
Table 3
nV/√Hz
+25
6
20
pA/√Hz
+25
1.5
5
pA/√Hz
+25
0.52
Table 3
pA/√Hz
-55
400K
Table 1
V/V
+25
1M
Table 1
V/V
+125
1M
Table 1
V/V
Slew Rate
Full Power Bandwidth
Rise and Fall Times
Overshoot
Settling Time
V_OUT = ±3V
V_PEAK = 10V, (Note 2)
V_OUT = ±200mV
V_OUT = ±200mV
To 0.1% for 10V Step
-55 to +125
10
-55 to +125
159
-55 to +125
50
-55 to +125
20
+25
4.5
5.4
85
Table 2
35
6
V/µs
kHz
ns
%
µs
To 0.01% for 10V Step
+25
6
10
µs
Output Short Circuit Current
Output Resistance
t < 10s, V_OUT = ±15V
Open Loop
+25
±35
±50
mA
+25
110
Table 3
Ω
Supply Current
No Load
+25
4.3
Table 1
mA
Minimum Supply Voltage
Functional Operation Only,
Other Parameters Will Vary
+25
±4
±5
V
All Intersil U.S. products are manufactured, assembled and tested utilizing ISO9000 quality systems.
Intersil Corporation’s quality certifications can be viewed at www.intersil.com/design/quality
Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without
notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and
reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result
from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries.
For information regarding Intersil Corporation and its products, see www.intersil.com
16
FN3931.1
August 17, 2005