ISL28005_14 Datasheet, PDF (14/15 Pages) Intersil Corporation – Micropower, Rail-to-Rail Input Current Sense Amplifier with Voltage Output

ISL28005
Revision History
The revision history provided is for informational purposes only and is believed to be accurate, but not warranted. Please go to web to make sure you have the latest Rev.
DATE
REVISION
CHANGE
October 24, 2013
FN6973.5
Added eight new Typical Performance Curves
1. Av = 100 Capacitive Load Drive Gain vs Freq
2. Av = 100 Capacitive Load Drive Phase vs Freq
3. Av = 50 Capacitive Load Drive Gain vs Freq
4. Av = 50 Capacitive Load Drive Phase vs Freq
5. Av = 20 Capacitive Load Drive Gain vs Freq
6. Av = 20 Capacitive Load Drive Phase vs Freq
7. High Side Operation Input Bias Currents
8. Low Side Operation Input Bias Currents
April 11, 2011
FN6973.4
Under Electrical Specifications Table:
Changed parameter from Is to Icc to clarify supply current.
Corrected location of the load in Figure 27. Moved Load from the ground side of the input sense circuit to the high side of the
voltage source.
September 2, 2010
May 12, 2010
April 12, 2010
April 7, 2010
February 3, 2010
December 14, 2009
FN6973.3
FN6973.2
FN6973.1
FN6973.0
Updated note in Min Max column of spec table from "Parameters with MIN and/or MAX limits are 100% tested at +25°C,
unless otherwise specified. Temperature limits established by characterization and are not production tested." to
"Compliance to datasheet limits is assured by one or more methods: production test, characterization and/or design."
Added -T7A tape and reel package options to Ordering Information Table for all packages.
Added Note 4 to Part Marking Column in “Ordering Information” on page 3.
Corrected hyperlinks in Notes 1 and 3 in “Ordering Information” on page 3.
Corrected ISL28005 hyperlink in “About Intersil” on page 14.
Added Eval boards to ordering info.
Added “Related Literature” on page 1
Updated Package Drawing Number in the “Ordering Information” on page 3 from MDP0038 to P50.64A.
Revised package outline drawing from MDP0038 to P5.064A on page 15. MDP0038 package contained 2 packages for both
the 5 and 6 Ld SOT-23. MDP0038 was obsoleted and the packages were separated and made into 2 separate package
outline drawings; P5.064A and P6.064A. Changes to the 5 Ld SOT-23 were to move dimensions from table onto drawing,
add land pattern and add JEDEC reference number.
-Page1:
Edited last sentence of paragraph 2.
Moved order of GAIN listings from 20, 50, 100 to 100, 50, 20 in the 3rd paragraph.
Under Features ....removed "Low Input Offset Voltage 250µV,max"
Under Features .... moved order of parts listing from 20, 50, 100 (from top to bottom) to 100, 50, 20.
-Page 3:
Removed coming soon on ISL28005FH50Z and ISL28005FH20Z and changes the order or listing them to 100, 50, 20.
-Page 5:
VOA test. Under conditions column ...deleted “20mV to”. It now reads ... Vsense = 100mV
SR test. Under conditions column ..deleted what was there. It now reads ... Pulse on RS+pin, See Figure 25
-Page 6:
ts test. Removed Gain = 100 and Gain = 100V/V in both description and conditions columns respectively.
-Page 9
Added Figure 25 and adjusted figure numbers to account for the added figure.
Initial Release
About Intersil
Intersil Corporation is a leader in the design and manufacture of high-performance analog, mixed-signal and power management
semiconductors. The company's products address some of the largest markets within the industrial and infrastructure, personal
computing and high-end consumer markets. For more information about Intersil, visit our website at www.intersil.com.
For the most updated datasheet, application notes, related documentation and related parts, please see the respective product
information page found at www.intersil.com. You may report errors or suggestions for improving this datasheet by visiting
www.intersil.com/en/support/ask-an-expert.html. Reliability reports are also available from our website at
http://www.intersil.com/en/support/qualandreliability.html#reliability
For additional products, see www.intersil.com/en/products.html
Intersil products are manufactured, assembled and tested utilizing ISO9001 quality systems as noted
in the quality certifications found at www.intersil.com/en/support/qualandreliability.html
Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time
without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be
accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third
parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries.
For information regarding Intersil Corporation and its products, see www.intersil.com
14
FN6973.5
October 24, 2013