HC5503PRC_14 Datasheet, PDF (11/11 Pages) Intersil Corporation – Low Cost SLIC For Large Telecom Switches

HC5503PRC
Quad Flat No-Lead Plastic Package (QFN)
Micro Lead Frame Plastic Package (MLFP)
2X
A
D
0.15 C A
9
D/2
6
INDEX
AREA 1
2
3
D1
D1/2
N
2X
0.15 C B
2X
0.15 C A
TOP VIEW
2X
0.15 C B
E1/2 E/2
E1
E
9
B
4X
A2
A / / _{0.10 C}
C
0.08 C
SEATING PLANE SIDE VIEW
A3 A1
9
4X P
(DATUM B)
4X P
(DATUM A)
6
INDEX
AREA
NX L
8
NX b ⁵
0.10 M C A B
D2
78
D2
2N
NX k
Ne
(Nd-1)Xe
REF.
BOTTOM VIEW
NX b
5
1
2
3
(Ne-1)Xe
E2
REF.
7
E2/2
8
9
CORNER
OPTION 4X
A1
SECTION "C-C"
CL
CL
L
L1 ¹⁰
L
L1 ¹⁰
e
CC
e
TERMINAL TIP
FOR ODD TERMINAL/SIDE
FOR EVEN TERMINAL/SIDE
L32.7x7
32 LEAD QUAD FLAT NO-LEAD PLASTIC PACKAGE
(COMPLIANT TO JEDEC MO-220VKKC ISSUE C)
SYMBOL
A
A1
A2
A3
b
D
D1
D2
E
E1
E2
e
k
L
L1
N
Nd
Ne
P
θ
MIN
0.80
-
-
0.23
4.55
4.55
0.25
0.50
-
-
-
MILLIMETERS
TYP
MAX
0.90
1.00
-
0.05
-
1.00
0.20 REF
0.28
0.38
7.00 BSC
6.75 BSC
4.70
4.85
7.00 BSC
6.75 BSC
4.70
4.85
0.65 BSC
-
-
0.60
0.75
-
0.15
32
8
8
-
0.60
-
12
NOTES
-
-
9
9
5, 8
-
9
7, 8
-
9
7, 8
-
-
8
10
2
3
3
9
9
Rev. 4 8/03
NOTES:
1. Dimensioning and tolerancing conform to ASME Y14.5-1994.
2. N is the number of terminals.
3. Nd and Ne refer to the number of terminals on each D and E.
4. All dimensions are in millimeters. Angles are in degrees.
5. Dimension b applies to the metallized terminal and is measured
between 0.15mm and 0.30mm from the terminal tip.
6. The configuration of the pin #1 identifier is optional, but must be
located within the zone indicated. The pin #1 identifier may be
either a mold or mark feature.
7. Dimensions D2 and E2 are for the exposed pads which provide
improved electrical and thermal performance.
8. Nominal dimensions are provided to assist with PCB Land
Pattern Design efforts, see Intersil Technical Brief TB389.
9. Features and dimensions A2, A3, D1, E1, P & θ are present
when Anvil singulation method is used and not present for saw
singulation.
10. Depending on the method of lead termination at the edge of the
package, a maximum 0.15mm pull back (L1) maybe present. L
minus L1 to be equal to or greater than 0.3mm.
11