ISL88694 Datasheet, PDF (1/7 Pages) Intersil Corporation – SMBus Accelerator (SMA)

®
Data Sheet
January 21, 2005
ISL88694
FN8239.1
SMBus Accelerator (SMA)
The ISL88694 SMBus accelerator (SMA) is a dual active
pull-up bus terminator designed to improve data
transmission speed on SMBus or similar 2-wire serial bus
interfaces. The ISL88694 is also compatible to the I²C serial
bus.
The SMA detects rising input transitions with two internal
voltage references and two comparators per channel. After
the voltage on a data line crosses the first threshold
(V_TRIPL), the boost pull-up current source is activated to
speed transition. After the voltage crosses the second
threshold (V_TRIPH), the boost pull-up current source is de-
activated, leaving an active pull-up current of 275µA on the
line. When both channels are HIGH, the pull-up current for
both lines is reduced to 100µA to save power. Internal logic
ensures that the active and boost pull-up current sources are
not activated during downward transitions.
The level for V_TRIPH is controlled by a bandgap voltage
referred to V_DD. This feature makes the switching behavior
invariant for all power supply voltages between 2.7V and
5.5V.
A noise filter on each channel prevents the circuit from
responding to input transitions that do not exceed a voltage-
time threshold. To activate the boost circuit, the input must
exceed V_TRIPL by 100Vns (typical) (See Figure 10).
The SMA permits operation of the bus at frequencies up to
100kHz, despite the capacitive loads of multiple devices
and/or long PC board traces. Enhanced ESD protection on
the accelerator pins are guaranteed to withstand 8kV ESD
(HBM) events.
The SMBus Accelerator provides an essential function in
SMBus applications because of distributed capacitance of
SMBus and multiple device input capacitances at various
nodes. By incorporating SMA, systems using SMBus or I²C
can reliably increase their bus load without the risk of data
loss.
Ordering Information
PART NUMBER
PACKAGE
TEMP RANGE (°C)
ISL88694IH5
5-pin SOT
-40 to 85
ISL88694IH5Z (Note) 5-pin SOT (Pb-Free)
-40 to 85
Add “-TK” suffix for tape and reel.
NOTE: Intersil Pb-free products employ special Pb-free material
sets; molding compounds/die attach materials and 100% matte tin
plate termination finish, which are RoHS compliant and compatible
with both SnPb and Pb-free soldering operations. Intersil Pb-free
products are MSL classified at Pb-free peak reflow temperatures that
meet or exceed the Pb-free requirements of IPC/JEDEC J STD-020.
Features
• Active Termination for SMBus lines
• Enhances System Bus Signal Rise Time
• Increases Bus Capacity While Guaranteeing Data Integrity
• 2.2mA Rise Time Supply Current
• 8kV ESD Protection on SDA and SCL Pins
• Wide Operating Voltage Range: 2.7V to 5.5V
• 2-Wire SMBus and I²C Compatible (100kHz)
• Small Package - SOT23-5
• Pin-for-Pin Compatible with the LTC1694
• Pb-Free Available (RoHS Compliant)
Target Applications
• Servers
• Data Acquisition
• Routers
• Battery Chargers
• Portable Instrumentation
• Notebook
• PC
• Facilities Tracking System
Pinout
ISL88694
(5 LD SOT-23)
TOP VIEW
V_DD
1
GND
2
N.C.
3
5 _SMBus1
4
SMBus2
1
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
1-888-INTERSIL or 321-724-7143 | Intersil (and design) is a registered trademark of Intersil Americas Inc.
Copyright Intersil Americas Inc. 2005. All Rights Reserved
All other trademarks mentioned are the property of their respective owners.