ISL28168 Datasheet, PDF (1/16 Pages) Intersil Corporation – 34μA Micro-power Single and Dual Rail-to-Rail Input-Output (RRIO) Low Input Bias Current Op Amps

®
Data Sheet
ISL28168, ISL28268
September 13, 2007
FN6378.2
34µA Micro-power Single and Dual Rail-to-
Rail Input-Output (RRIO) Low Input Bias
Current Op Amps
The ISL28168 and ISL28268 are micro-power operational
amplifiers optimized for single supply operation over a power
supply range of 2.4VDC to 5.5VDC. These devices draw
minimal supply current and operate rail-to-rail at the input
and output, while providing excellent DC-accuracy, noise
and output drive specifications. Competing devices seriously
degrade these parameters to achieve micro-power supply
current.
The parts feature an Input Range Enhancement Circuit
(IREC) which enables them to maintain CMRR performance
for input voltages greater than the positive supply. The input
signal is capable of swinging 0.25V above the positive
supply and to 100mV below the negative supply with only a
slight degradation of the CMRR performance. The output
operation is rail-to-rail.
The 1/f corner of the voltage noise spectrum is at 100Hz.
This results in low frequency noise performance which can
only be found on devices with an order of magnitude higher
supply current.
ISL28168 and ISL28268 can be operated from one lithium
cell or two Ni-Cd batteries. The ISL28168 contains an enable
pin feature that allows the device to be shutdown when not in
use.
Ordering Information
PART NUMBER
(Note)
PART
PACKAGE
MARKING (Pb-free)
PKG.
DWG. #
ISL28168FHZ-T7* GACA
6 Ld SOT-23 MDP0038
ISL28168FHZ-T7A* GACA
6 Ld SOT-23 MDP0038
Coming Soon
ISL28268FBZ-T7*
8 Ld SOIC
MDP0027
Coming Soon
ISL28268FUZ-T7*
8 Ld MSOP MDP0043
* “-T7” and “-T7A” suffix are for tape and reel. Please refer to TB347
for details on reel specifications.
NOTE: These Intersil Pb-free plastic packaged products employ
special Pb-free material sets; molding compounds/die attach
materials and 100% matte tin plate PLUS ANNEAL - e3 termination
finish, which is RoHS compliant and compatible with both SnPb and
Pb-free soldering operations. Intersil Pb-free products are MSL
classified at Pb-free peak reflow temperatures that meet or exceed
the Pb-free requirements of IPC/JEDEC J STD-020.
Features
• 34µA typical supply current
• 10pA typical input bias current
• 200kHz gain bandwidth product
• 2.4V to 5.5V single supply voltage range
• Rail-to-rail input and output
• Enable pin (ISL28168 only)
• Pb-free (RoHS compliant)
Applications
• Battery- or solar-powered systems
• 4mA to 20mA current loops
• Handheld consumer products
• Medical devices
• Sensor amplifiers
• ADC buffers
• DAC output amplifiers
Pinouts
ISL28168
(6 LD SOT-23)
TOP VIEW
OUT 1
V- 2
+-
IN+ 3
6 V+
5 EN
4 IN-
ISL28268
(8 LD SOIC)
TOP VIEW
ISL28268
(8 LD MSOP)
TOP VIEW
OUT_A 1
IN-_A 2
IN+_A 3
V- 4
-+
+-
8 V+
OUT_A 1
7 OUT_B IN-_A 2
6 IN-_B IN+_A 3
5 IN+_B
V- 4
-+
+-
8 V+
7 OUT_B
6 IN-_B
5 IN+_B
1
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
1-888-INTERSIL or 1-888-468-3774 | Intersil (and design) is a registered trademark of Intersil Americas Inc.
Copyright © Intersil Americas Inc. 2007. All Rights Reserved.
All other trademarks mentioned are the property of their respective owners.