ISL22326 Datasheet, PDF (1/13 Pages) Intersil Corporation – Dual Digitally Controlled Potentiometers

ISL22326
®
Dual Digitally Controlled Potentiometers (XDCP™)
Data Sheet
July 17, 2006
FN6176.0
Low Noise, Low Power, I²C^® Bus,
128 Taps
The ISL22326 integrates two digitally controlled
potentiometers (XDCP) and non-volatile memory on a
monolithic CMOS integrated circuit.
The digitally controlled potentiometers are implemented with
a combination of resistor elements and CMOS switches. The
position of the wipers are controlled by the user through the
I²C bus interface. Each potentiometer has an associated
volatile Wiper Register (WR) and a non-volatile Initial Value
Register (IVR) that can be directly written to and read by the
user. The contents of the WR controls the position of the
wiper. At power-up the device recalls the contents of the two
DCP’s IVR to the corresponding WRs.
The DCPs can be used as three-terminal potentiometers or
as two-terminal variable resistors in a wide variety of
applications including control, parameter adjustments, and
signal processing.
Pinout
ISL22326
(14 LD TSSOP)
TOP VIEW
V_CC
1
SHDN
2
RH0
3
RL0
4
RW0
5
A2
6
SCL
7
14 A1
13 ^A0
12
RH1
11 RL1
10 RW1
9
GND
8
SDA
Features
• Two potentiometers in one package
• 128 resistor taps
• I²C serial interface
- Three address pins, up to eight devices/bus
• Non-volatile storage of wiper position
• Wiper resistance: 70Ω typical @ 3.3V
• Shutdown mode
• Shutdown current 5µA max
• Power supply: 2.7V to 5.5V
• 50kΩ or 10kΩ total resistance
• High reliability
- Endurance: 1,000,000 data changes per bit per register
- Register data retention: 50 years @ T <55°C
• 14 Ld TSSOP
• Pb-free plus anneal product (RoHS compliant)
Ordering Information
PART NUMBER
PART MARKING
RESISTANCE OPTION
(kΩ)
TEMP. RANGE
(°C)
PACKAGE
PKG. DWG. #
ISL22326UFV14Z
(Notes 1, 2)
22326 UFVZ
50
-40 to +125
14 Ld TSSOP
M14.173
(Pb-free)
ISL22326WFV14Z
(Notes 1, 2)
22326 WFVZ
10
-40 to +125
14 Ld TSSOP
M14.173
(Pb-free)
NOTES:
1. Intersil Pb-free plus anneal products employ special Pb-free material sets; molding compounds/die attach materials and 100% matte tin plate
termination finish, which are RoHS compliant and compatible with both SnPb and Pb-free soldering operations. Intersil Pb-free products are
MSL classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J STD-020.
2. Add “-TK” suffix for 1,000 Tape and Reel option
1
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
1-888-INTERSIL or 1-888-468-3774 | Intersil (and design) and XDCP are registered trademarks of Intersil Americas Inc.
Copyright Intersil Americas Inc. 2006. All Rights Reserved
All other trademarks mentioned are the property of their respective owners.