HS-508BRH Datasheet, PDF (1/4 Pages) Intersil Corporation – Radiation Hardened 8 Channel CMOS Analog Multiplexer with Overvoltage Protection

®
Data Sheet
August 11, 2009
HS-508BRH
FN4824.2
Radiation Hardened 8 Channel CMOS
Analog Multiplexer with Overvoltage
Protection
The HS-508BRH is a dielectrically isolated, radiation
hardened, CMOS analog multiplexer incorporating an
important feature; it withstands analog input voltages much
greater than the supplies. This is essential in any system
where the analog inputs originate outside the equipment.
They can withstand a continuous input up to 10V greater than
either supply, which eliminates the possibility of damage when
supplies are off, but input signals are present. Equally
important, it can withstand brief input transient spikes of
several hundred volts; which otherwise would require complex
external protection networks. Necessarily, ON resistance is
somewhat higher than similar unprotected devices, but very
low leakage current combine to produce low errors.
Reference Application Notes 520 and 521 for further
information on the HS-508BRH multiplexer in general.
The HS-508BRH has been specifically designed to meet
exposure to radiation environments. Operation from -55°C to
+125°C is guaranteed.
Features
• Electrically Screened to SMD # 5962-96742
• QML Qualified per MIL-PRF-38535 Requirements
• Radiation Environment
- Gamma Dose (γ) . . . . . . . . . . . . . . . . . 3 x 10⁵ Rad (Si)
- Dielectrically Isolated Device Islands
- SEP >100 Mev-mg/cm²
• Analog/Digital Overvoltage Protection
• ESD Rated to 3kV
• Fail Safe with Power Loss (No Latchup)
• Break-Before-Make Switching
• (Typ) DTL/TTL and CMOS Compatible Threshold
• Analog Signal Range. . . . . . . . . . . . . . . . . . . . . . . . . . . . ±15V
• Fast Access Time
• Supply Current at 1MHz Address Toggle . . . . . .4mA (Typ)
• Standby Power . . . . . . . . . . . . . . . . . . . . . . . .7.5mW (Typ)
• Pb-Free (RoHS Compliant)
Specifications for Rad Hard QML devices are controlled
by the Defense Supply Center in Columbus (DSCC). The
SMD numbers listed here must be used when ordering.
Detailed Electrical Specifications for these devices are
contained in SMD 5962-96742. A “hot-link” is provided
on our homepage for downloading.
www.intersil.com/spacedefense/newsafclasst.asp
Ordering Information
ORDERING NUMBER
(Note)
INTERNAL
MKT. NUMBER
PART MARKING
TEMP. RANGE
(°C)
PACKAGE
(Pb-Free)
PKG. DWG.
5962F9674202QEC
HS1-508BRH-8
Q 5962F96 74202QEC
-55 to +125 16 Ld SBDIP
D16.3
5962F9674202QXC
HS9-508BRH-8
Q 5962F96 74202QXC
-55 to +125 16 Ld FLATPACK K16.A
5962F9674202VEC
HS1-508BRH-Q
Q 5962F96 74202VEC
-55 to +125 16 Ld SBDIP
D16.3
5962F9674202VXC
HS9-508BRH-Q
Q 5962F96 74202VXC
-55 to +125 16 Ld FLATPACK K16.A
HS1-508BRH/PROTO HS1-508BRH/PROTO
HS1- 508BRH /PROTO
-55 to +125 16 Ld SBDIP
D16.3
HS9-508BRH/PROTO HS9-508BRH/PROTO
HS9- 508BRH /PROTO
-55 to +125 16 Ld FLATPACK K16.A
NOTE: These Intersil Pb-free Hermetic packaged products employ 100% Au plate - e4 termination finish, which is RoHS compliant and compatible
with both SnPb and Pb-free soldering operations.
1
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
1-888-INTERSIL or 1-888-468-3774 | Intersil (and design) is a registered trademark of Intersil Americas Inc.
Copyright Intersil Americas Inc. 2001, 2009. All Rights Reserved
All other trademarks mentioned are the property of their respective owners