HS-302RH-T Datasheet, PDF (1/2 Pages) Intersil Corporation – Radiation Hardened CMOS Dual DPST Analog Switch

Data Sheet
HS-302RH-T
July 1999 File Number 4603.1
Radiation Hardened
CMOS Dual DPST Analog Switch
Intersil’s Satellite Applications Flow^TM (SAF) devices are fully
tested and guaranteed to 100kRAD Total Dose. These QML
Class T devices are processed to a standard flow intended
to meet the cost and shorter lead-time needs of large
volume satellite manufacturers, while maintaining a high
level of reliability.
The HS-302RH-T analog switch is a monolithic device
fabricated using Radiation Hardened CMOS technology and
the Intersil dielectric isolation process for latch-up free
operation. Improved total dose hardness is obtained by
layout (thin oxide tabs extending to a channel stop) and
processing (hardened gate oxide). These switches offer low-
resistance switching performance for analog voltages up to
the supply rails. “ON” resistance is low and stays reasonably
constant over the full range of operating voltage and current.
“ON” resistance also stays reasonably constant when
exposed to radiation, being typically 30Ω pre-rad and 35Ω
post 100kRAD(Si). This device provide break-before-make
switching.
Specifications
Specifications for Rad Hard QML devices are controlled by
the Defense Supply Center in Columbus (DSCC). The SMD
numbers listed below must be used when ordering.
Detailed Electrical Specifications for the HS-302RH-T
are contained in SMD 5962-95812. A “hot-link” is provided
from our website for downloading.
www.intersil.com/spacedefense/newsafclasst.asp
Intersil’s Quality Management Plan (QM Plan), listing all
Class T screening operations, is also available on our
website.
www.intersil.com/spacedefense/newsafclasst.asp
Ordering Information
ORDERING
NUMBER
PART
NUMBER
TEMP.
RANGE
(^oC)
5962R9581201TCC
HS1-302RH-T
-55 to 125
5962R9581201TXC
HS9-302RH-T
-55 to 125
NOTE: Minimum order quantity for -T is 150 units through
distribution, or 450 units direct.
Features
• QML Class T, Per MIL-PRF-38535
• Radiation Performance
- Gamma Dose (γ) 1 x 10⁵ RAD(Si)
• No Latch-Up, Dielectrically Isolated Device Islands
• Pin for Pin Compatible with Intersil HI-302 Series Analog
Switches
• Analog Signal Range 15V
• Low Leakage . . . . . . . . . . . . . . . . 100nA (Max, Post Rad)
• Low R_ON . . . . . . . . . . . . . . . . . . . . . 60Ω (Max, Post Rad)
• Low Operating Power . . . . . . . . . . 100µA (Max, Post Rad)
Pinouts
HS1-302RH-T (SBDIP), CDIP2-T14
TOP VIEW
NC ¹
S3 ²
D3 ³
D1 ⁴
S1 ⁵
IN1 ⁶
GND ⁷
14 V+
13 S4
12 D4
11 D2
10 S2
9 IN2
8 V-
HS9-302RH-T (FLATPACK), CDFP3-F14
TOP VIEW
1
NC
2
S3
3
D3
4
D1
5
S1
6
IN1
7
GND
14
V+
13
S4
12
D4
11
D2
10
S2
9
IN2
8
V-
Functional Diagram
IN
N
P
D
TRUTH TABLE
LOGIC
ALL SWITCHES
0
OFF
1
ON
1
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
www.intersil.com or 407-727-9207 | Copyright © Intersil Corporation 1999
Satellite Applications Flow™ (SAF) is a trademark of Intersil Corporation.