HS-26C31RH Datasheet, PDF (1/3 Pages) Intersil Corporation – Radiation Hardened Quad Differential Line Driver

®
Data Sheet
HS-26C31RH
May 27, 2010
FN3401.5
Radiation Hardened Quad Differential Line
Driver
The Intersil HS-26C31RH is a quad differential line driver
designed for digital data transmission over balanced lines
and meets the requirements of EIA standard RS-422.
Radiation hardened CMOS processing assures low power
consumption, high speed, and reliable operation in the most
severe radiation environments.
The HS-26C31RH accepts CMOS signal levels and converts
them to RS-422 compatible outputs. This circuit uses special
outputs that enable the drivers to power-down without loading
down the bus. Enable and disable pins allow several devices to
be connected to the same data source and addressed
independently.
Specifications
Specifications for Rad Hard QML devices are controlled by
the Defense Supply Center in Columbus (DSCC). The SMD
numbers listed here must be used when ordering.
Detailed Electrical Specifications for these devices are
contained in SMD 5962-96663. A “hot-link” is provided
on our homepage for downloading.
www.intersil.com/military/
Features
• Electrically Screened to SMD # 5962-96663
• QML Qualified per MIL-PRF-38535 Requirements
• 1.2 Micron Radiation Hardened CMOS
- Total Dose Up to . . . . . . . . . . . . . . . . . . . . 300kRAD(Si)
• Latchup Free
• EIA RS-422 Compatible Outputs (Except for IOS)
• CMOS Inputs
• High Impedance Outputs when Disabled or Powered
Down
• Low Power Dissipation . . . . . . . . . 2.75mW Standby (Max)
• Single 5V Supply
• Low Output Impedance . . . . . . . . . . . . . . . . . 10Ω or Less
• Full -55°C to +125°C Military Temperature Range
Applications
• Line Transmitter for MIL-STD-1553 Serial Data Bus
Ordering Information
ORDERING
NUMBER
INTERNAL
MKT. NUMBER
5962F9666301QEC
HS1-26C31RH-8
5962F9666301QXC
HS9-26C31RH-8
5962F9666301VEC
HS1-26C31RH-Q
5962F9666301VXC
HS9-26C31RH-Q
HS1-26C31RH/PROTO HS1-26C31RH/PROTO
HS9-26C31RH/PROTO HS9-26C31RH/PROTO
5962F9666301V9A
HSO-26C31RH-Q
PART MARKING
Q 5962F96 6630QEC
Q 5962F96 66301QXC
Q 5962F96 66301VEC
Q 5962F96 66301VXC
HS1- 26C31RH/PROTO
HS9- 26C31RH/PROTO
TEMP. RANGE
(°C)
PACKAGE
-55 to +125 16 LD SBDIP
-55 to +125 16 LD FLATPACK
-55 to +125 16 LD SBDIP
-55 to +125 16 LD FLATPACK
-55 to +125 16 LD SBDIP
-55 to +125 16 LD FLATPACK
-55 to +125
PKG.
DWG. #
D16.3
K16.A
D16.3
K16.A
D16.3
K16.A
1
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
1-888-INTERSIL or 1-888-468-3774 | Intersil (and design) is a registered trademark of Intersil Americas Inc.
Copyright Intersil Americas Inc. 2000, 2008, 2010. All Rights Reserved
Satellite Applications Flow™ (SAF) is a trademark of Intersil Corporation. All other trademarks mentioned are the property of their
respective owners.