|
HS-2100RH Datasheet, PDF (1/2 Pages) Intersil Corporation – Radiation Hardened High Frequency Half Bridge Driver | |||
|
Data Sheet
HS-2100RH
June 1999 File Number 4562.3
Radiation Hardened High Frequency
Half Bridge Driver
The Radiation Hardened HS-2100RH is a high frequency,
100V Half Bridge N-Channel MOSFET Driver IC, which is a
functional, pin-to-pin replacement for the Intersil HIP2500
and the industry standard 2110 types. The low-side and
high-side gate drivers are independently controlled. This
gives the user maximum ï¬exibility in dead-time selection and
driver protocol.
In addition, the device has on-chip error detection and
correction circuitry, which monitors the state of the high-side
latch and compares it to the HIN signal. If they disagree, a
set or reset pulse is generated to correct the high-side latch.
This feature protects the high-side latch from SEUs.
Undervoltage on the high-side supply forces HO low. When
that supply returns to a valid voltage, HO will go to the state
of HIN. Undervoltage on the low-side supply forces both LO
and HO low. When that supply becomes valid, LO returns to
the LIN state and HO returns to the HIN state.
Speciï¬cations for Rad Hard QML devices are controlled
by the Defense Supply Center in Columbus (DSCC). The
SMD numbers listed here must be used when ordering.
Detailed Electrical Speciï¬cations for the HS-2100RH are
contained in SMD 5962-99536. A âhot-linkâ is provided
on our homepage for downloading.
www.intersil.com/spacedefense/space.asp
This link will not be available until the SMD is ï¬nalized.
Ordering Information
ORDERING NUMBER
5962F9953601VXC
5962F9953601QXC
HS9-2100RH/Proto
INTERSIL MKT.
TEMP.
NUMBER
RANGE (oC)
HS9-2100RH-Q
-55 to 125
HS9-2100RH-8
-55 to 125
HS9-2100RH/Proto -55 to 125
Features
⢠Electrically Screened to DESC SMD # 5962-99536
⢠QML Qualiï¬ed per MIL-PRF-38535 Requirements
⢠Radiation Environment
- Maximum Total Dose . . . . . . . . . . . . . . 3 x 105 RAD(SI)
- DI RSG Process Provides Latch-up Immunity
- Vertical Architecture Provides Low Dose Rate Immunity
⢠Bootstrap Supply Max Voltage to 120V
⢠Drives 1000pF Load at 1MHz with Rise and Fall Times of
45ns (Typ)
⢠1A (Typ) Peak Output Current
⢠Independent Inputs for Non-Half Bridge Topologies
⢠Low DC Power Consumption . . . . . . . . . . . . . 60mW (Typ)
⢠Operates with VDD = VCC Over 12V to 20V Range
⢠Supply Undervoltage Protection
Applications
⢠High Frequency Switch-Mode Power Supplies
⢠Drivers for Inductive Loads
⢠DC Motor Drivers
Pinout
HS-2100RH
FLATPACK (CDFP4-F16)
TOP VIEW
LO
1
16
NC
COM
2
15
VSS
VCC
3
14
LIN
NC
4
13
SD
NC
5
12
HIN
VS
6
11
VDD
VB
7
10
NC
HO
8
9
NC
1
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
1-888-INTERSIL or 321-724-7143 | Copyright © Intersil Corporation 1999
|
▷ |