HIP6004 Datasheet, PDF (1/12 Pages) Intersil Corporation – Buck and Synchronous-Rectifier (PWM) Controller and Output Voltage Monitor

Data Sheet
HIP6004
March 2000 File Number 4275.2
Buck and Synchronous-Rectifier (PWM)
Controller and Output Voltage Monitor
The HIP6004 provides complete control and protection for a
DC-DC converter optimized for high-performance
microprocessor applications. It is designed to drive two
N-Channel MOSFETs in a synchronous-rectified buck
topology. The HIP6004 integrates all of the control, output
adjustment, monitoring and protection functions into a single
package.
The output voltage of the converter is easily adjusted and
precisely regulated. The HIP6004 includes a 5-input
digital-to-analog converter (DAC) that adjusts the output
voltage from 2.1V_DC to 3.5V_DC in 0.1V increments and from
1.3V_DC to 2.1V_DC in 0.05V steps. The precision reference
and voltage-mode regulator hold the selected output voltage
to within ±1% over temperature and line voltage variations.
The HIP6004 provides simple, single feedback loop,
voltage-mode control with fast transient response. It includes
a 200kHz free-running triangle-wave oscillator that is
adjustable from below 50kHz to over 1MHz. The error
amplifier features a 15MHz gain-bandwidth product and
6V/µs slew rate which enables high converter bandwidth for
fast transient performance. The resulting PWM duty ratio
ranges from 0% to 100%.
The HIP6004 monitors the output voltage with a window
comparator that tracks the DAC output and issues a Power
Good signal when the output is within ±10%. The HIP6004
protects against over-current conditions by inhibiting PWM
operation. Built-in over-voltage protection triggers an
external SCR to crowbar the input supply. The HIP6004
monitors the current by using the r_DS(ON) of the upper
MOSFET which eliminates the need for a current sensing
resistor.
Ordering Information
TEMP.
PART NUMBER RANGE (^oC)
PACKAGE
HIP6004CB
0 to 70 20 Ld SOIC
This data sheet describes a pre-released product.
PKG.
NO.
M20.3
Alpha Micro™ is a trademark of Digital Computer Equipment Corporation.
Pentium® is a registered trademark of Intel Corporation.
PowerPC™ is a registered trademark of IBM.
Features
• Drives Two N-Channel MOSFETs
• Operates from +5V or +12V Input
• Simple Single-Loop Control Design
- Voltage-Mode PWM Control
• Fast Transient Response
- High-Bandwidth Error Amplifier
- Full 0% to 100% Duty Ratio
• Excellent Output Voltage Regulation
- ±1% Over Line Voltage and Temperature
• 5-Bit Digital-to-Analog Output Voltage Selection
- Wide Range . . . . . . . . . . . . . . . . . . . 1.3V_DC to 3.5V_DC
- 0.1V Binary Steps . . . . . . . . . . . . . . . 2.1V_DC to 3.5V_DC
- 0.05V Binary Step. . . . . . . . . . . . . . . 1.3V_DC to 2.1V_DC
• Power-Good Output Voltage Monitor
• Over-Voltage and Over-Current Fault Monitors
- Does Not Require Extra Current Sensing Element,
Uses MOSFETs r_DS(ON)
• Small Converter Size
- Constant Frequency Operation
- 200kHz Free-Running Oscillator Programmable from
50kHz to over 1MHz
Applications
• _{Power Supply for Pentium®, Pentium Pro, PowerPC™ and}
Alpha™ Microprocessors
• _{High-Power 5V to 3.xV DC-DC Regulators}
• _{Low-Voltage Distributed Power Supplies}
Pinout
HIP6004
(SOIC)
TOP VIEW
VSEN 1
OCSET 2
SS 3
VID0 4
VID1 5
VID2 6
VID3 7
VID4 8
COMP 9
FB 10
20 RT
19 OVP
18 VCC
17 LGATE
16 PGND
15 BOOT
14 UGATE
13 PHASE
12 PGOOD
11 GND
1
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
1-888-INTERSIL or 321-724-7143 | Copyright © Intersil Corporation 2000