HIP4083_04 Datasheet, PDF (1/10 Pages) Intersil Corporation – 80V, 300mA Three Phase High Side Driver

®
Data Sheet
July 2004
HIP4083
FN4223.2
80V, 300mA Three Phase High Side Driver
The HIP4083 is a three phase high side N-channel MOSFET
driver, specifically targeted for PWM motor control. Two
HIP4083 may be used together for 3 phase full bridge
applications (see application block diagram). Alternatively,
the lower gates may be controlled directly from a buffered
microprocessor output.
Unlike other members of the HIP408x family, the HIP4083
has no built in turn-on delay. Each output (AHO, BHO, and
CHO) will turn-on 65ns after its input is switched low.
Likewise, each output will turn-off 60ns after its input is
switched high. Very short and very long dead times are
possible when two HIP4083 are used to drive a full bridge.
This dead time is controlled by the input signal timing.
The HIP4083 does not have a built in charge pump.
Therefore, the bootstrap capacitors must be recharged on a
periodic basis by initiating a short refresh pulse. In most
bridge applications, this will happen automatically every time
the lower FETs turn-on and the upper FETs turn-off.
However, it is still possible to use the HIP4083 in
applications that require the high side FETs to be on for
extended periods of time. This can be easily accomplished
by sending a short refresh pulse to the DIS pin.
The HIP4083 has reduced drive current compared to the
HIP4086 making it ideal for low to moderate power
applications. The HIP4083 is optimized for applications
where size and cost are important. For high power
applications driving large power FETs, the HIP4086 is
recommended.
Pinout
HIP4083
(PDIP, SOIC)
TOP VIEW
AHI 1
BHI 2
CHI 3
DIS 4
V_SS 5
AHB 6
AHO 7
AHS 8
16 CHB
15 CHO
14 CHS
13 UVLO
12 ^VDD
11 BHB
10 BHO
9 BHS
Features
• Independently Drives Three High Side N-Channel
MOSFETs in Three Phase Bridge Configuration
• Bootstrap Supply Max Voltage to 95VDC
• Bias Supply Operation from 7V to 15V
• Drives 1000pF Load with Typical Rise Times of 35ns and
Fall Times of 30ns
• CMOS/TTL Compatible Inputs
• Programmable Undervoltage Protection
• Pb-free Available
Applications
• Brushless Motors
• High Side Switches
• AC Motor Drives
• Switched Reluctance Motor Drives
Ordering Information
TEMP.
PART NUMBER RANGE (°C)
PACKAGE
PKG.
DWG. #
HIP4083AB
-40 to 105 16 Ld SOIC
M16.15
HIP4083ABZ (Note) -40 to 105 16 Ld SOIC (Pb-free) M16.15
HIP4083AP
-40 to 105 16 Ld PDIP
E16.3
HIP4083APZ (Note) -40 to 105 16 Ld PDIP (Pb-free) E16.3
NOTE: Intersil Pb-free products employ special Pb-free material
sets; molding compounds/die attach materials and 100% matte tin
plate termination finish, which is compatible with both SnPb and
Pb-free soldering operations. Intersil Pb-free products are MSL
classified at Pb-free peak reflow temperatures that meet or exceed
the Pb-free requirements of IPC/JEDEC J Std-020B.
1
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
1-888-INTERSIL or 321-724-7143 | Intersil (and design) is a registered trademark of Intersil Americas Inc.
Copyright Harris Corporation 1995. Copyright Intersil Americas Inc. 2003, 2004. All Rights Reserved
All other trademarks mentioned are the property of their respective owners.