HIP0082 Datasheet, PDF (1/12 Pages) Intersil Corporation – Quad Power Drivers with Serial Diagnostic Interface

HIP0082, HIP0084
PRELIMINARY
May 1998
Quad Power Drivers with
Serial Diagnostic Interface
Features
• Low Side Power MOSFET Output Drivers
- Output Voltage Clamp (Typ) . . . . . . . . . . . . . . . . 80V
- Maximum Output Current . . . . . . . . . . . . . . . . 5A/2A
- Output r_DS(ON) (T_J = 150^oC) (Max) . . . . . 0.57Ω/0.62Ω
• Controlled Slew Rate Switching (HIP0084)
• Single Pulse Energy Rating . . . . . . . . . . . . . . . . . 70mJ
• Programmable Output Over Current Shutdown Threshold
- Bit Select 2A or 5A on Outputs 3 and 4
• Output Protection
- Output Over Current Shutdown
- Output Over Voltage Clamp
- Over Temperature Diagnostic Feedback
• Diagnostics for Shorts, Opens and Over Temperature
• Synchronous Serial Interface with
- 22-Bit Serial Diagnostic Register
- SPI Compatible Interface
• Single 5V Supply Operation with CMOS Logic Inputs
• Supply Current, I_CC, Full Load (Typ) . . . . . . . . . <10mA
•
Low θ_JC Power SIP Packages
SIP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3^oC/W
PSOP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2^oC/W
• -40^oC to 125^oC Operating Temperature
Applications
• Drivers For
- Solenoids
- Relays
- Power Output
- Lamps
- Injectors
- Steppers
- Motors
- Displays
• System Use
- Automotive
- Appliances
- Industrial
- Robotics
Description
The HIP0082 and HIP0084 Quad Power Drivers contain four
individually protected NDMOS transistor switches to drive
inductive and resistive loads such as: fuel injectors, relays,
solenoids, etc. The outputs are low-side switches driven by
active-low CMOS logic inputs. Each output is protected
against excessive current due to a short-circuit. Internal
drain-to-gate zener diodes provide output clamping for over
voltage. An integrated charge pump allows operation from a
single 5V logic supply. Diagnostic circuits provide ground
short (SG), supply short (SC) and open load (OL) detection
for each of the four output stages and indicate over tempera-
ture. Diagnostic information may be read via a synchronous
serial interface. Six bits of write/store data sets a long or
short OL fault delay time for each output and sets Outputs 3
and 4 to a 2A or 5A current shutdown threshold. The
HIP0084 is specified with controlled slew rate switching.
Both types are fabricated in a Power BiMOS IC process and
are intended for use in automotive and other applications with a
wide range of temperature and electrical stress. They are par-
ticularly suited for driving high-current inductive loads requiring
high breakdown voltage and high output current. Both types
available in the 15 lead Power SIP or 20 lead PSOP packages
with low thermal resistance for high power applications.
Ordering Information
PART
NUMBER
HIP0082AS1
HIP0084AS1
HIP0082AS2
HIP0082AB
HIP0084AB
TEMP.
RANGE(°C)
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
PACKAGE
15 Ld SIP
15 Ld SIP
15 Ld SIP
20 Ld PSOP
20 Ld PSOP
PKG.
NO.
Z15.05A
Z15.05A
Z15.05B
M20.433
M20.433
Pinouts
HIP0082, HIP0084 (SIP)
TOP VIEW
HEAT SINK TAB INTERNALLY CONNECTED
TO PIN 8 GROUND (V_SS)
15
IN3
14
OUT3
13
IN1
12
OUT1
11
R/W
10
V_CC
9
RST
8
GND (V_SS)
7
TXD
6
CLK
5
CS
4
OUT2
3
IN2
2
OUT4
1
IN4
HIP0082, HIP0084 (PSOP W/HEAT SLUG)
TOP VIEW
INTEGRAL COPPER
HEAT SINK ‘SLUG’
FOR PCB CONTACT
OR EXT. HEAT SINK
GND (SLUG)
1
IN4
2
OUT4
3
IN2
4
GND (V_SS)
5
OUT2
6
CS
7
CLK
8
TXD
9
GND (SLUG)
10
20
GND (SLUG)
19
IN3
18
OUT3
17
IN1
16
GND (V_SS)
15
OUT1
14
R/W
13
V_CC
12
RST
11
GND (SLUG)
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
http://www.intersil.com or 407-727-9207 | Copyright © Intersil Corporation 1999
1
File Number 3643.4