HI-574A_01 Datasheet, PDF (1/17 Pages) Intersil Corporation – Complete, 12-Bit A/D Converters with Microprocessor Interface

TM
Data Sheet
HI-574A, HI-674A
June 2001
File Number 3096.5
itle
I-
4A,
-
4A,
-
4)
bjec
omp
e,
-Bit
D
nver
s
th
crop
esso
erfa
utho
)
eyw
s
tersi
rpor
on,
ico
ucto
/D,
C,
sh,
nver
, bit,
le
dem
Complete, 12-Bit A/D Converters with
Microprocessor Interface
The HI-X74(A) is a complete 12-bit, Analog-to-Digital
Converter, including a +10V reference clock, three-state
outputs and a digital interface for microprocessor control.
Successive approximation conversion is performed by two
monolithic dice housed in a 28 lead package. The bipolar
analog die features the Intersil Dielectric Isolation process,
which provides enhanced AC performance and freedom
from latch-up.
Custom design of each IC (bipolar analog and CMOS digital)
has yielded improved performance over existing versions of
this converter. The voltage comparator features high PSRR
plus a high speed current-mode latch, and provides precise
decisions down to 0.1 LSB of input overdrive. More than 2X
reduction in noise has been achieved by using current
instead of voltage for transmission of all signals between the
analog and digital ICs. Also, the clock oscillator is current
controlled for excellent stability over temperature.
The HI-X74(A) offers standard unipolar and bipolar input
ranges, laser trimmed for specified linearity, gain and offset
accuracy. The low noise buried zener reference circuit is
trimmed for minimum temperature coefficient.
Power requirements are +5V and ±12V to ±15V, with typical
dissipation of 385mW (HI-574A/674A) at 12V.
Features
• Complete 12-Bit A/D Converter with Reference and Clock
• Full 8-Bit, 12-Bit or 16-Bit Microprocessor Bus Interface
• Bus Access Time . . . . . . . . . . . . . . . . . . . . . . . . . . . 150ns
• No Missing Codes Over Temperature
• Minimal Setup Time for Control Signals
• Fast Conversion Times
- HI-574A (Max) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25µs
- HI-674A (Max) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15µs
• Low Noise, via Current-Mode Signal Transmission
Between Chips
• Byte Enable/Short Cycle (A_O Input)
- Guaranteed Break-Before-Make Action, Eliminating Bus
Contention During Read Operation. Latched by Start
Convert Input (To Set the Conversion Length)
• Supply Voltage . . . . . . . . . . . . . . . . . . . . . . ±12V to ±15V
Applications
• Military and Industrial Data Acquisition Systems
• Electronic Test and Scientific Instrumentation
• Process Control Systems
Pinout
(PDIP, SBDIP)
TOP VIEW
+5V SUPPLY, V_LOGIC 1
DATA MODE SEL, 12/8 2
CHIP SEL, CS 3
BYTE ADDR/SHORT
CYCLE, A_O
4
READ/CONVERT, R/C ⁵
CHIP ENABLE, CE 6
+12V/+15V SUPPLY, V_CC 7
+10V REF, REF OUT 8
ANALOG
COMMON, AC
9
REFERENCE INPUT ¹⁰
-12V/-15V SUPPLY, V_EE 11
BIPOLAR OFFSET
BIP OFF
12
10V INPUT 13
20V INPUT 14
28 STATUS, STS
27 DB11 MSB
26 DB10
25 DB9
24 DB8
23 DB7
22 DB6
21 DB5
DIGITAL
DATA
OUTPUTS
20 DB4
19 DB3
18 DB2
17 DB1
16 DB0 LSB
15
DIG COMMON,
DC
1
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
1-888-INTERSIL or 321-724-7143 | Intersil and Design is a trademark of Intersil Americas Inc. | Copyright © Intersil Americas Inc. 2001