HA-5004883 Datasheet, PDF (1/5 Pages) Intersil Corporation – 100MHz Current Feedback Amplifier

July 1998
HA-5004/883 _{NOc1oT-n8R8taE8cC-ItNOo}^®_{TMuErMRTESeNcILDhnoEriDcwaFlwOSwRu.piNnptEoeWrrst} ^{iCDl.ecEnoStmIeGr/tNasStc}
100MHz Current Feedback Amplifier
Features
Description
• This Circuit is Processed in Accordance to MIL-STD-
883 and is Fully Conformant Under the Provisions of
Paragraph 1.2.1.
• Slew Rate . . . . . . . . . . . . . . . . . . . . . . 1000V/µs (Min)
1200V/µs (Typ)
• Output Current . . . . . . . . . . . . . . . . . . . . ±80mA (Min)
±100mA (Typ)
• Drives . . . . . . . . . . . . . . . . . . . ±8.0V into 100Ω (Min)
±9.5V into 100Ω (Typ)
• V_SUPPLY . . . . . . . . . . . . . . . . . . . . . . . . . ±5V to ±18V
• Thermal Overload Protection and Output Flag
• Bandwidth Nearly Independent of Gain
• Output Enable/Disable
Applications
• Unity Gain Video/Wideband Buffer
• Video Gain Block
• High Speed Peak Detector
• Fiber Optic Transmitters
• Zero Insertion Loss Transmission Line Drivers
• Current to Voltage Converter
• Radar Systems
The HA-5004/883 current feedback amplifier is a video/wideband
amplifier optimized for low gain applications. The design is based
on current-mode feedback which allows the amplifier to achieve
higher closed loop bandwidth than voltage-mode feedback oper-
ational amplifiers. Since feedback is employed, the HA-5004/883
can offer better gain accuracy and lower distortion than open
loop buffers. Unlike conventional op amps, the bandwidth and
rise time of the HA-5004/883 are nearly independent of closed
loop gain. The 100MHz bandwidth at unity gain reduces to only
65MHz at a gain of 10. The HA-5004/883 may be used in place
of a conventional op amp with a significant improvement in speed
power product.
Several features have been designed in for added value. A ther-
mal overload feature protects the part against excessive junction
temperature by shutting down the output. If this feature is not
needed, it can be inhibited via a TTL input (TOI). A TTL chip
enable/disable (OE) input is also provided; when the chip is dis-
abled its output is high impedance. Finally, an open collector out-
put flag (TOL) is provided to indicate the status of the chip. The
status flag goes low to indicate when the chip is disabled due to
either the internal Thermal Overload shutdown or the external
disable.
In order to maximize bandwidth and output drive capacity, inter-
nal current limiting is not provided. However, current limiting may
be applied via the V_C+ and V_C- pins which provide power sepa-
rately to the output stage.
Ordering Information
PART NUMBER
HA1-5004/883
TEMP. RANGE
(^oC)
PACKAGE
-55 to +125 14 Lead CerDIP
Pinout
HA-5004/883
(CERDIP)
TOP VIEW
V_C + ¹
OUT 2
+BAL 3
-BAL ⁴
V+ 5
TOI 6
OE 7
14 _{VC -}
13 _V-
-
12 FB
+
11 IN
10 TOL
9 GND
8 NC
CAUTION: These devices are sensitive to electrostatic discharge. Users should follow proper IC Handling Procedures.
Copyright © Harris Corporation 1998
1
Spec Number 511053-883
File Number 3706.1