EL7156_15 Datasheet, PDF (1/11 Pages) Intersil Corporation – High Performance Pin Driver

Data Sheet
September 1, 2015
EL7156
FN7280.4
High Performance Pin Driver
The EL7156 high performance pin driver with three-state is
suited to many ATE and level-shifting applications. The 3.5A
peak drive capability makes this part an excellent choice
when driving high capacitance loads.
The output pin OUT is connected to input pins VH or VL
respectively, depending on the status of the IN pin. When the
OE pin is active low, the output is placed in the three-state
mode. The isolation of the output FETs from the power
supplies enables VH and VL to be set independently,
enabling level-shifting to be implemented. Related to the
EL7155, the EL7156 adds a lower supply pin VS- and makes
VL an isolated and independent input. This feature adds
applications flexibility and improves switching response due
to the increased enhancement of the output FETs.
This pin driver has improved performance over existing pin
drivers. It is specifically designed to operate at voltages
down to 0V across the switch elements while maintaining
good speed and ON-resistance characteristics.
Available in the 8 Ld SOIC and 8 Ld PDIP packages, the
EL7156 is specified for operation over the full -40°C to
+85°C temperature range.
Features
• Clocking speeds up to 40MHz
• 15ns t_R/t_Fat 2000pF C_LOAD
• 0.5ns rise and fall times mismatch
• 0.5ns t_ON-t_OFF prop delay mismatch
• 3.5pF typical input capacitance
• 3.5A peak drive
• Low ON-resistance of 3.5Ω
• High capacitive drive capability
• Operates from 4.5V to 16.5V
• Pb-free plus anneal available (RoHS compliant)
Applications
• ATE/burn-in testers
• Level shifting
• IGBT drivers
• CCD drivers
Pinout
EL7156
(8 LD PDIP, SOIC)
TOP VIEW
VS+ 1
L
OE 2
O
G
I
IN 3
C
GND 4
8 VH
7 OUT
6 VL
5 VS-
Ordering Information
PART NUMBER
PART MARKING TAPE & REEL
PKG
PKG. DWG. #
EL7156CNZ (Note)
(No longer available, recommended replacement: EL7156CSZ)
EL7156CN Z
-
8 Ld PDIP* (Pb-free) MDP0031
EL7156CSZ (Note)
7156CSZ
-
8 Ld SOIC (Pb-free) MDP0027
EL7156CSZ-T7 (Note)
7156CSZ
7”
8 Ld SOIC (Pb-free) MDP0027
EL7156CSZ-T13 (Note)
7156CSZ
13”
8 Ld SOIC (Pb-free) MDP0027
NOTE: Intersil Pb-free plus anneal products employ special Pb-free material sets; molding compounds/die attach materials and 100% matte tin plate
termination finish, which are RoHS compliant and compatible with both SnPb and Pb-free soldering operations. Intersil Pb-free products are MSL
classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J STD-020.
*Pb-free PDIPs can be used for through hole wave solder processing only. They are not intended for use in Reflow solder processing applications.
1
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
1-888-INTERSIL or 1-888-468-3774 | Intersil (and design) is a registered trademark of Intersil Americas LLC
Copyright Intersil Americas LLC 2003, 2005, 2007, 2015. All Rights Reserved
All other trademarks mentioned are the property of their respective owners.