EL7155_06 Datasheet, PDF (1/10 Pages) Intersil Corporation – High Performance Pin Driver

®
Data Sheet
March 9, 2006
EL7155
FN7279.2
High Performance Pin Driver
The EL7155 high performance pin driver with 3-state is
suited to many ATE and level-shifting applications. The 3.5A
peak drive capability makes this part an excellent choice
when driving high capacitance loads.
Output pins OUT_H and OUT_L are connected to input pins V_H
and V_L respectively, depending on the status of the IN pin.
One of the output pins is always in tri-state, except when the
OE pin is active low, in which case both outputs are in
3-state mode. The isolation of the output FETs from the
power supplies enables V_H and V_L to be set independently,
enabling level-shifting to be implemented.
This pin driver has improved performance over existing pin
drivers. It is specifically designed to operate at voltages
down to 0V across the switch elements while maintaining
good speed and on-resistance characteristics.
Available in 8 Ld SO and 8 Ld PDIP packages, the EL7155
is specified for operation over the full -40°C to +85°C
temperature range.
Pinout
EL7155
(8 LD PDIP, SO)
TOP VIEW
VS+ 1
L
OE 2
o
g
i
IN 3
c
GND 4
8 VH
7 OUTH
6 OUTL
5 VL
Features
• Clocking speeds up to 40MHz
• 15ns tr/tf at 2000pF C_LOAD
• 0.5ns rise and fall times mismatch
• 0.5ns T_ON-T_OFF prop delay mismatch
• 3.5pF typical input capacitance
• 3.5A peak drive
• Low on resistance of 3.5Ω
• High capacitive drive capability
• Operates from 4.5V up to 16.5V
• Pb-free plus anneal available (RoHS compliant)
Applications
• ATE/burn-in testers
• Level shifting
• IGBT drivers
• CCD drivers
Ordering Information
PART TAPE &
PKG.
PART NUMBER MARKING REEL PACKAGE DWG. #
EL7155CN
EL7155CN
- 8 Ld PDIP MDP0031
EL7155CS
7155CS
- 8 Ld SO
MDP0027
EL7155CS-T7 7155CS
7” 8 Ld SO
MDP0027
EL7155CS-T13 7155CS
13” 8 Ld SO
MDP0027
EL7155CSZ
(Note)
7155CSZ
- 8 Ld SO
MDP0027
(Pb-free)
EL7155CSZ-T7 7155CSZ
(Note)
7” 8 Ld SO
(Pb-free)
MDP0027
EL7155CSZ-T13 7155CSZ
(Note)
13” 8 Ld SO
(Pb-free)
MDP0027
NOTE: Intersil Pb-free plus anneal products employ special Pb-free
material sets; molding compounds/die attach materials and 100%
matte tin plate termination finish, which are RoHS compliant and
compatible with both SnPb and Pb-free soldering operations. Intersil
Pb-free products are MSL classified at Pb-free peak reflow
temperatures that meet or exceed the Pb-free requirements of
IPC/JEDEC J STD-020.
1
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
1-888-INTERSIL or 1-888-468-3774 | Intersil (and design) is a registered trademark of Intersil Americas Inc.
Copyright © Intersil Americas Inc. 2003, 2005-2006. All Rights Reserved.
All other trademarks mentioned are the property of their respective owners.