EL6173 Datasheet, PDF (1/2 Pages) Intersil Corporation – 3-Channel Laser Diode Driver w/Oscillator & APC Amplifier

®
Data Sheet
June 14, 2004
EL6173
FN7213
3-Channel Laser Diode Driver w/Oscillator
& APC Amplifier
The EL6173 is a high performance
three-channel laser driver that
provides controlled current to a
grounded laser diode. Write channels 2 and 3 can provide
up to 200mA per channel of DC or pulsed current, with
switching speeds of approximately one nanosecond rise/fall
time. All three channels are summed together at the I_OUT
output, allowing the user to create multilevel waveforms in
order to optimize laser diode performance. The level of the
output current is set by an analog voltage applied to an
external resistor which converts the voltage into a current at
the I_IN pin (virtually ground). The current seen at this pin is
then amplified to become a current source at pin I_OUT.
An on-chip 500MHz oscillator is provided to allow output
current modulation when in any mode. This is turned on
when the OSCEN pin is held high. Complete control of
amplitude and frequency is set by two external resistors
connected to ground at pins R_FREQ and R_AMP (see graphs
in this data sheet for further explanation.)
Output current pulses are enabled when an ‘L’ signal is
applied to the OUTEN pin. No output current flows when
OUTEN is ‘H’ and additional laser diode protection is
provided since the OUTEN input will float high when open.
Complete I_OUT shut-off is also achieved by holding the
ENABLE pin low, which will override all other control pins.
The EL6173 also includes a fast-settling APC amplifier
designed to interface directly with the front end monitor
diode and the sample-and-hold amplifier for read and write
power control. Its 100MHz bandwidth and 30ns settling time
enable up to 16X CD-RW design.
Ordering Information
PART
NUMBER
PACKAGE TAPE & REEL PKG. DWG. #
EL6173CU
16-Pin QSOP
-
MDP0040
EL6173CU-T7 16-Pin QSOP
7”
MDP0040
EL6173CU-T13 16-Pin QSOP
13”
MDP0040
EL6173CUZ 16-Pin QSOP
-
(See Note)
(Pb-free)
MDP0040
EL6173CUZ- 16-Pin QSOP
7”
T7 (See Note)
(Pb-free)
MDP0040
EL6173CUZ- 16-Pin QSOP
13”
T13 (See Note) (Pb-free)
MDP0040
NOTE: Intersil Pb-free products employ special Pb-free material
sets; molding compounds/die attach materials and 100% matte tin
plate termination finish, which is compatible with both SnPb and
Pb-free soldering operations. Intersil Pb-free products are MSL
classified at Pb-free peak reflow temperatures that meet or exceed
the Pb-free requirements of IPC/JEDEC J Std-020B.
Features
• “Shrink-Small” outline package
• Voltage-controlled output current source to 200mA per
channel, requiring one external set resistor per channel
• Current-controlled output current source to 200mA per
channel
• Rise time = 0.8ns
• Fall time = 0.8ns
• On-chip oscillator with frequency and amplitude control by
use of external resistors to ground
• Oscillator to 500MHz
• Oscillator to 100mA_PK/PK
• Single +5V supply (±10%)
• Disable feature for power-up protection and power savings
• Fast-settling APC amplifier
• Pb-free Available as an Option
Applications
• CD-RW applications
• Writable optical drives
• Laser diode current switching
Get FULL DATASHEET
1
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
1-888-INTERSIL or 321-724-7143 | Intersil (and design) is a registered trademark of Intersil Americas Inc.
Copyright © Intersil Americas Inc. 2003-2004. All Rights Reserved. Elantec is a registered trademark of Elantec Semiconductor, Inc.
All other trademarks mentioned are the property of their respective owners.