EL5177_07 Datasheet, PDF (1/11 Pages) Intersil Corporation – 550MHz Differential Twisted-Pair Driver

®
Data Sheet
May 10, 2007
EL5177
FN7344.4
550MHz Differential Twisted-Pair Driver
The EL5177 is a high bandwidth amplifier with an output in
differential form. It is primarily targeted for applications such
as driving twisted-pair lines or any application where
common mode injection is likely to occur. The input signal
can be in either single-ended or differential form but the
output is always in differential form.
On the EL5177, two feedback inputs provide the user with
the ability to set the device gain (stable at minimum gain of
one.)
The output common mode level is set by the reference pin
(REF), which has a -3dB bandwidth of 110MHz. Generally,
this pin is grounded but it can be tied to any voltage
reference.
Both outputs (OUT+, OUT-) are short circuit protected to
withstand temporary overload condition.
The EL5177 is available in the 10 Ld MSOP package and is
specified for operation over the full -40°C to +85°C
temperature range.
See also EL5174 (EL5177 in 8 Ld MSOP.)
Features
• Fully differential inputs, outputs, and feedback
• Differential input range ±2.3V
• 550MHz 3dB bandwidth
• 1100V/µs slew rate
• Low distortion at 20MHz
• Single 5V or dual ±5V supplies
• 40mA maximum output current
• Low power, 12.5mA typical supply current
• Pb-free plus anneal available (RoHS compliant)
Applications
• Twisted-pair drivers
• Differential line drivers
• VGA over twisted-pair
• ADSL/HDSL drivers
• Single ended to differential amplification
• Transmission of analog signals in a noisy environment
Pinout
EL5177
(10 LD MSOP)
TOP VIEW
FBP 1
10 OUT+
IN+ 2
REF 3
+
-
IN- 4
9 VS-
8 VS+
7 EN
FBN 5
6 OUT-
Ordering Information
PART NUMBER
PART MARKING
TAPE & REEL
PACKAGE
PKG. DWG. #
EL5177IY
3
-
10 Ld MSOP (3.0mm)
MDP0043
EL5177IY-T7
3
7”
10 Ld MSOP (3.0mm)
MDP0043
EL5177IY-T13
3
13”
10 Ld MSOP (3.0mm)
MDP0043
EL5177IYZ (Note)
BAAKA
-
10 Ld MSOP (Pb-free) (3.0mm) MDP0043
EL5177IYZ-T7 (Note) BAAKA
7”
10 Ld MSOP (Pb-free) (3.0mm) MDP0043
EL5177IYZ-T13 (Note) BAAKA
13”
10 Ld MSOP (Pb-free) (3.0mm) MDP0043
NOTE: Intersil Pb-free plus anneal products employ special Pb-free material sets; molding compounds/die attach materials and 100% matte tin plate
termination finish, which are RoHS compliant and compatible with both SnPb and Pb-free soldering operations. Intersil Pb-free products are MSL
classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J STD-020.
1
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
1-888-INTERSIL or 1-888-468-3774 | Intersil (and design) is a registered trademark of Intersil Americas Inc.
Copyright © Intersil Americas Inc. 2003-2005, 2007. All Rights Reserved.
All other trademarks mentioned are the property of their respective owners.