CDP68HC68T1_06 Datasheet, PDF (1/24 Pages) Intersil Corporation – CMOS Serial Real-Time Clock With RAM and Power Sense/Control

®
Data Sheet
CDP68HC68T1
March 17, 2006
FN1547.7
CMOS Serial Real-Time Clock With RAM
and Power Sense/Control
The CDP68HC68T1 Real-Time Clock provides a
time/calendar function, a 32 byte static RAM, and a 3 wire
Serial Peripheral Interface (SPI Bus). The primary function of
the clock is to divide down a frequency input that can be
supplied by the on-board oscillator in conjunction with an
external crystal or by an external clock source. The internal
oscillator can operate with a 32kHz, 1MHz, 2MHz, or 4MHz
crystal. An external clock source with a 32kHz, 1MHz, 2MHz,
4MHz, 50Hz or 60Hz frequency can be used to drive the
CDP68HC68T1. The time registers hold seconds, minutes,
and hours, while the calendar registers hold day-of-week,
date, month, and year information. The data is stored in BCD
format. In addition, 12 or 24 hour operation can be selected.
In 12 hour mode, an AM/PM indicator is provided. The T1
has a programmable output which can provide one of seven
outputs for use elsewhere in the system.
Computer handshaking is controlled with a “wired-OR” interrupt
output. The interrupt can be programmed to provide a signal as
the result of: 1) an alarm programmed to occur at a
predetermined combination of seconds, minutes, and hours; 2)
one of 15 periodic interrupts ranging from sub-second to once
per day frequency; 3) a power fail detect. The PSE output and
the V_SYS input are used for external power control. The CPUR
output is available to reset the processor under power-down
conditions. CPUR is enabled under software control and can
also be activated via the CDP68HC68T1’s watchdog. If
enabled, the watchdog requires a periodic toggle of the CE pin
without a serial transfer.
Pinouts
CDP68HC68T1 (PDIP, SOIC)
TOP VIEW
CLKOUT 1
CPUR 2
INT 3
SCK 4
MOSI 5
MISO 6
CE 7
V_SS 8
16 V_DD
15 XTAL OUT
14 XTAL IN
13 V_BATT
12 V_SYS
11 LINE
10 POR
9 PSE
Features
• SPI (Serial Peripheral Interface)
• Full Clock Features
- Seconds, Minutes, Hours (12/24, AM/PM), Day of
Week, Date, Month, Year (0-99), Automatic Leap Year
• 32 Word x 8-Bit RAM
• Seconds, Minutes, Hours Alarm
• Automatic Power Loss Detection
• Low Minimum Standby (Timekeeping) Voltage . . . . . 2.2V
• Selectable Crystal or 50/60Hz Line Input
• Buffered Clock Output
• Battery Input Pin that Powers Oscillator and also
Connects to V_DD Pin When Power Fails
• Three Independent Interrupt Modes
- Alarm
- Periodic
- Power-Down Sense
• Pb-Free Plus Anneal Available (RoHS Compliant)
CDP68HC68T1 (SOIC)
TOP VIEW
CLK OUT 1
CPUR 2
INT 3
NC 4
SCK 5
MOSI 6
MISO 7
CE 8
V_SS 9
PSE 10
20 VDD
19 XTAL OUT
18 XTAL IN
17 NC
16 V_BATT
15 V_SYS
14 NC
13 NC
12 LINE
11 POR
1
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
1-888-INTERSIL or 1-888-352-6832 | Intersil (and design) is a registered trademark of Intersil Americas Inc.
Copyright Harris Corporation 1997. Copyright Intersil Americas Inc. 2001, 2004-2006. All Rights Reserved
All other trademarks mentioned are the property of their respective owners.