80C196KC Datasheet, PDF (10/25 Pages) Intel Corporation – COMMERCIAL/EXPRESS CHMOS MICROCONTROLLER

8XC196KC 8XC196KC20
DC CHARACTERISTICS (Over Specified Operating Conditions) (Continued)
Symbol
Description
Min Typ Max Units
Test Conditions
V_OH1
I_OH1
Output High Voltage
(Quasi-bidirectional Outputs)
Logical 1 Output Current in Reset
on P2 0 Do not exceed this
or device may enter test modes
V_CC ^b 0 3
V_CC ^b 0 7
V_CC ^b 1 5
b_{0 8}
V I_OH ^{e b}10 mA
V I_OH ^{e b}30 mA
V I_OH ^{e b}60 mA
mA V_IH ^e V_CC ^b 1 5V
I_IL2
Logical 0 Input Current in Reset
on P2 0 Maximum current that
must be sunk by external
device to ensure test mode entry
TBD mA V_IN ^e 0 45V
I_IH1
Logical 1 Input Current
Maximum current that external
device must source to initiate NMI
a_{200 mA VIN} e _VCC e _{2 4V}
I_LI
I_LI1
I_TL
I_IL
I_IL1
I_CC
I_CC
I_IDLE
Input Leakage Current (Std Inputs)
Input Leakage Current (Port 0)
1 to 0 Transition Current (QBD Pins)
Logical 0 Input Current (QBD Pins)
Ports 3 and 4 in Reset
Active Mode Current in Reset
(8XC196KC)
Active Mode Current in Reset
(8XC196KC20)
Idle Mode Current (8XC196KC)
I_IDLE Idle Mode Current (8XC196KC20)
I_PD
Powerdown Mode Current
I_REF A D Converter Reference Current
R_RST Reset Pullup Resistor
6K
C_S
Pin Capacitance (Any Pin to V_SS)
g10 mA 0 ^k V_IN ^k V_CC b 0 3V
g3 mA 0 ^k V_IN ^k V_REF
b_{650 mA VIN} e _{2 0V}
b_{70 mA VIN} e _{0 45V}
b_{70 mA VIN} e _{0 45V}
65 75 mA XTAL1 ^e 16 MHz
V_CC ^e V_PP ^e V_REF ^e 5 5V
80 92 mA XTAL1 ^e 20 MHz
V_CC ^e V_PP ^e V_REF ^e 5 5V
17 25 mA XTAL1 ^e 16 MHz
V_CC ^e V_PP ^e V_REF ^e 5 5V
21 30 mA XTAL1 ^e 20 MHz
V_CC ^e V_PP ^e V_REF ^e 5 5V
8 15 mA V_CC ^e V_PP ^e V_REF ^e 5 5V
2
5
mA V_CC ^e V_PP ^e V_REF ^e 5 5V
65K X V_CC ^e 5 5V V_IN ^e 4 0V
10 pF
NOTES
1 All pins except RESET and XTAL1
2 Violating these specifications in Reset may cause the part to enter test modes
3 Commercial specifications apply to express parts except where noted
4 QBD (Quasi-bidirectional) pins include Port 1 P2 6 and P2 7
5 Standard Outputs include AD0–15 RD WR ALE BHE INST HSO pins PWM P2 5 CLKOUT RESET Ports 3 and 4
TXD P2 0 and RXD (in serial mode 0) The V_OH specification is not valid for RESET Ports 3 and 4 are open-drain outputs
6 Standard Inputs include HSI pins READY BUSWIDTH RXD P2 1 EXTINT P2 2 T2CLK P2 3 and T2RST P2 4
7 Maximum current per pin must be externally limited to the following values if V_OL is held above 0 45V or V_OH is held
below V_CC b 0 7V
I_OL on Output pins 10 mA
I_OH on quasi-bidirectional pins self limiting
I_OH on Standard Output pins 10 mA
8 Maximum current per bus pin (data and control) during normal operation is g3 2 mA
9 During normal (non-transient) conditions the following total current limits apply
Port 1 P2 6
HSO P2 0 RXD RESET
P2 5 P2 7 WR BHE
AD0 – AD15
RD ALE INST–CLKOUT
I_OL 29 mA
I_OL 29 mA
I_OL 13 mA
I_OL 52 mA
I_OL 13 mA
I_OH is self limiting
I_OH 26 mA
I_OH 11 mA
I_OH 52 mA
I_OH 13 mA
10