SAFC167CRLMHA Datasheet, PDF (63/89 Pages) Infineon Technologies AG – 16-Bit Single-Chip Microcontroller

C167CR
C167SR
Electrical Parameters
Table 11 DC Characteristics (Operating Conditions apply)¹⁾ (cont’d)
Parameter
Symbol Limit Values Unit Test Condition
Min. Max.
Output high voltage³⁾
(PORT0, PORT1, Port 4, ALE,
RD, WR, BHE, CLKOUT,
RSTOUT)
V_OH CC 2.4
–
0.9 V_DD –
V I_OH = -2.4 mA
V I_OH = -0.5 mA
Output high voltage³⁾
(all other outputs)
Input leakage current (Port 5)
V_OH1 CC
I_OZ1 CC
2.4
0.9 V_DD
–
–
–
±200
V I_OH = -1.6 mA
V I_OH = -0.5 mA
nA 0 V < V_IN < V_DD
Input leakage current
(all other)⁴⁾
I_OZ2 CC –
RSTIN inactive current⁵⁾
RSTIN active current⁵⁾
READY/RD/WR inact. current⁸⁾
READY/RD/WR active current⁸⁾
ALE inactive current⁸⁾
ALE active current⁸⁾
Port 6 inactive current⁸⁾
Port 6 active current⁸⁾
PORT0 configuration current⁹⁾
I_RSTH6)
I_RSTL7)
I_RWH6)
I_RWL7)
I_ALEL6)
I_ALEH7)
I_P6H6)
I_P6L7)
I_P0H6)
I_P0L7)
–
-100
–
-500
–
500
–
-500
–
-100
±500
-10
–
-40
–
40
–
-40
–
-10
–
nA 0.45 V < V_IN <
V_DD
µA V_IN = V_IH1
µA V_IN = V_IL
µA V_OUT = 2.4 V
µA V_OUT = V_OLmax
µA V_OUT = V_OLmax
µA V_OUT = 2.4 V
µA V_OUT = 2.4 V
µA V_OUT = V_OL1max
µA V_IN = V_IHmin
µA V_IN = V_ILmax
XTAL1 input current
I_IL CC –
±20
µA 0 V < V_IN < V_DD
Pin capacitance¹⁰⁾
(digital inputs/outputs)
C_IO CC –
10
pF f = 1 MHz;
T_A = 25 °C
1) Keeping signal levels within the levels specified in this table, ensures operation without overload conditions.
For signal levels outside these specifications also refer to the specification of the overload current I_OV.
2) Valid in bidirectional reset mode only.
3) This specification is not valid for outputs which are switched to open drain mode. In this case the respective
output will float and the voltage results from the external circuitry.
4) This parameter is not valid for pins READY, ALE, RD, and WR while the respective pull device is on.
5) These parameters describe the RSTIN pull-up, which equals a resistance of ca. 50 to 250 kΩ.
6) The maximum current may be drawn while the respective signal line remains inactive.
7) The minimum current must be drawn in order to drive the respective signal line active.
8) This specification is valid during Reset and during Hold-mode or Adapt-mode. During Hold-mode Port 6 pins
are only affected, if they are used (configured) for CS output and the open drain function is not enabled. The
READY-pull-up is always active, except for Power-down mode.
Data Sheet
61
V3.3, 2005-02