ITS716G Datasheet, PDF (6/14 Pages) Infineon Technologies AG – Smart High-Side Power Switch For Industrial Applications Four Channels: 4 x 140mΩ

PROFET® ITS 716G
Parameter and Conditions, each of the four channels Symbol
at Tj = -40...+150°C, V_bb = 12 V unless otherwise specified
Operating Parameters
Operating voltage
Undervoltage switch off¹⁰⁾
T_j =-40...25°C:
T_j =125°C:
Overvoltage protection¹²⁾
I _bb = 40 mA
Standby current¹³⁾
V_IN = 0; see diagram page 11
T_j =-40°C...25°C:
T_j =150°C:
T_j =125°C:
Off-State output current (included in I_bb(off))
V_IN = 0; each channel
Operating current ¹⁴⁾, V_IN = 5V,
I_GND = I_GND1 + I_GND2,
one channel on:
all channels on:
V_bb(on)
V_{bb(u so)}
V_bb(AZ)
I_bb(off)
I_L(off)
I_GND
Protection Functions¹⁵⁾
Current limit, Vout = 0V, (see timing diagrams, page 12)
Tj ^=-40°C:
Tj ^=25°C:
Tj ^=+150°C:
Repetitive short circuit current limit,
T_j = T_jt
each channel
two,three or four parallel channels
(see timing diagrams, page 12)
Initial short circuit shutdown time T_j,start =25°C:
Vout = 0V
(see timing diagrams on page 12)
Output clamp (inductive load switch off)¹⁶⁾
at VON(CL) = Vbb - VOUT, I_L= 40 mA
Thermal overload trip temperature
Thermal hysteresis
I_L(lim)
I_L(SCr)
t_off(SC)
V_ON(CL)
T_jt
∆T_jt
Values
Unit
min typ max
5.5
-- 40 V
--
-- 4.5 V
--
-- 4.5¹¹⁾
41 47 52 V
--
9 16 µA
--
-- 24
--
-- 16¹¹⁾
--
1
5 µA
-- 0.5 0.9 mA
-- 1.9 3.3
--
--
--
9
5
--
-- 6.5
-- 6.5
--
2
41 47
150
--
-- 10
14 A
--
--
-- A
--
-- ms
52 V
-- °C
-- K
10) _{is the voltage, where the device doesn´t change it´s switching condition for 15ms after the supply voltage}
falling below the lower limit of Vbb(on)
11) _{not subject to production test, specified by design}
12) _{Supply voltages higher than Vbb(AZ) require an external current limit for the GND and status pins (a 150Ω}
resistor for the GND connection is recommended). See also VON(CL) in table of protection functions and
circuit diagram on page 9.
13) _{Measured with load; for the whole device; all channels off}
14) _{Add IST, if IST > 0}
15) _{Integrated protection functions are designed to prevent IC destruction under fault conditions described in the}
data sheet. Fault conditions are considered as "outside" normal operating range. Protection functions are
not designed for continuous repetitive operation.
16) _{If channels are connected in parallel, output clamp is usually accomplished by the channel with the lowest}
V_ON(CL)
Infineon Technologies AG
6 of 14
2006-Mar-23