V23806-A8-C1 Datasheet, PDF (2/3 Pages) Infineon Technologies AG – Multimode 1300 nm LED Fast Ethernet/FDDI/ATM 10 dB 155 MBd 1x9 Transceiver

The data rate is scalable and the ATM protocol is the basis of
the broadband public networks being standardized in the Inter-
national Telegraph and Telephone Consultative Committee
(CCITT). ATM can also be used in local private applications.
FDDI is a Dual Token Ring standard developed in the U.S. by the
Accredited National Standards Committee (ANSC) X3T9, within
the Technical Committee X3T9.5. It is applied to the local area
networks of stations, transferring data at 100 Mbits/s with a
125 MBaud transmission rate. LCF FDDI is specially developed
for short distance applications of up to 500 m (fiber-to-the-desk)
as compared to 2 km for backbone applications.
Fast Ethernet was developed because of the higher bandwidth
requirement in local area networking. It is based on the proven
effectiveness of millions of installed Ethernet systems.
The Infineon multimode transceiver is a single unit comprised
of a transmitter, a receiver, and an SC receptacle. This design
frees the customer from many alignment and PC board layout
concerns. The modules are designed for low cost applications.
TECHNICAL DATA
The electro-optical characteristics described in the following
tables are valid only for use under the recommended operating
conditions.
Recommended Operating Conditions
Parameter
Symbol Min.
Ambient Temperature
Power Supply Voltage
Supply Current +5 V⁽¹⁾
Transmitter
T_AMB
V_CC–V_EE
I_CC
0
4.75
140
Data Input
High Voltage
V_IH–V_CC –1165
Data Input
Low Voltage
V_IL–V_CC –1810
Input Data Rise/Fall, t_R, t_F
0.4
20%–80%
Data High Time⁽²⁾
t_on
Receiver
Output Current
Input Duty Cycle
Distortion
l_O
t_DCD
Input Data
t_DDj
Dependent Jitter
Input Random Jitter t_RJ
Input Center
l_C
Wavelength
1260
Electrical Output
R_L
Load⁽³⁾
Typ. Max.
70
5.0 5.25
170 210
Units
°C
V
mA
–880 mV
–1475 mV
1.3 ns
1000
25 mA
1.0 ns
0.76
1380 nm
50
W
Notes
1. For V_CC–V_EE (min., max.). 50% duty cycle. The supply current
(I_CC2+I_CC3) does not include the load drive current (Icc1). Add max.
45 mA for the three outputs. Load is 50 Ω into V_CC –2V.
2. To maintain good LED reliability, the device should not be held in the
ON state for more than the specified time. Normal operation should
be done with 50% duty cycle.
3. To achieve proper PECL output levels the 50 Ω termination should be
done to V_CC –2 V. For correct termination see the application notes.
Transmitter Electro-Optical Characteristics
Transmitter
Data Rate
Symbol Min. Typ. Max. Units
DR
200 MBd
Launched Power (Average) P_O
into 62.5 µm Fiber^{(1, 2)}
Center Wavelength^{(2, 3)}
λ_C
Spectral Width (FWHM)^{(2, 4)} D_l
Output Rise/Fall Time,
10%–90%^{(2, 5)}
t_R, t_F
–20 –17 –14 dBm
1270
0.6
1360 nm
200
2.5 ns
Extinction Ratio
ER
(Dynamic)^{(2, 6)}
10 %
Overshoot
Duty Cycle Distortion^{(7, 8)}
Data Dependent Jitter^{(7, 9)}
Random Jitter^{(7, 10)}
OS
t_DCD
t_DDJ
t_RJ
10 %
0.6 ns
0.3
0.6
Notes
1. Measured at the end of 5 meters of 62.5/125/0.275 graded index
fiber using calibrated power meter and a precision test ferrule.
Cladding modes are removed. Values valid for EOL and worst-case
temperature.
2. The input data pattern is a 12.5 MHz square wave pattern.
3. Center wavelength is defined as the midpoint between the two
50% levels of the optical spectrum of the LED.
4. Spectral width (full width, half max) is defined as the difference
between 50% levels of the optical spectrum of the LED.
5. 10% to 90% levels. Measured using the 12.5 MHz square wave
pattern with an optoelectronic measurement system (detector
and oscilloscope) having 3 dB bandwidth ranging from less than
0.1 MHz to more than 750 MHz.
6. Extinction Ratio is defined as PL/PH x 100%. Measurement system
as in Note 5.
7. Test method as for FDDI-PMD. Jitter values are peak-to-peak.
8. Duty Cycle Distortion is defined as 0.5 [(width of wider state) minus
(width of narrower state)]. It is measured with stream of Idle
Symbols (62.5 MHz square wave).
9. Measured with the same pattern as for FDDI-PMD.
10.Measured with the Halt Line state (12.5 MHz square wave).
Fiber Optics
V23806-A8-C1, Multimode 1300 nm LED ATM 10 dB 155 MBd 1x9 Transceiver
2