TLE7250GVIO Datasheet, PDF (16/23 Pages) Infineon Technologies AG – High Speed CAN Transceiver

TLE7250GVIO
Electrical Characteristics
Table 6 Electrical Characteristics (cont’d)
4.75 V < V_CC < 5.25 V; 3.0 V < V_IO < 5.25 V; R_L = 60 Ω; -40 °C < T_j < +150 °C; all voltages with respect to ground;
positive current flowing into the pin; unless otherwise specified.
Pos. Parameter
Symbol Limit Values
Unit Remarks
Min. Typ. Max.
Not Enable Input NEN
7.1.18 “High” level input voltage
threshold
7.1.19 “Low” level input voltage
threshold
7.1.20 NEN pull-up resistance
7.1.21 NEN input hysteresis
Bus Receiver
V_NEN,H
–
V_NEN,L
R_NEN
V_HYS(NEN)
0.3 ×
V_IO
10
–
0.5 ×
V_IO
0.4 ×
V_IO
25
200
0.7 × V
V_IO
–
V
stand-by mode
normal-operating mode
50 kΩ –
–
mV ¹⁾
7.1.22 Differential receiver threshold V_DIFF,(D) –
“dominant”
0.75 0.9 V normal-operating mode
7.1.23 Differential receiver threshold V_DIFF,(R) 0.5
“recessive”
0.65 –
normal-operating mode
7.1.24 Differential receiver input
range “dominant”
V_diff,rdN
0.9
–
5.0 V ¹⁾ normal-operating mode
7.1.25 Differential receiver input
range “recessive”
V_diff,drN
-1.0 –
0.5 V ¹⁾ normal-operating mode
7.1.26 Common mode range
CMR
7.1.27 Differential receiver hysteresis V_diff,hys
7.1.28 CANH, CANL input resistance R_i
7.1.29 Differential input resistance R_diff
7.1.30 Input resistance deviation
ΔR_i
between CANH and CANL
7.1.31 Input capacitance CANH,
C_IN
CANL versus GND
7.1.32 Differential input capacitance C_InDiff
Bus Transmitter
-12 –
12
–
100 –
10
20
30
20
40
60
-3
–
3
–
20
40
–
10
20
V V_CC = 5 V
mV ¹⁾
kΩ “recessive” state
kΩ “recessive” state
% ¹⁾ “recessive” state
pF ¹⁾ V_TxD = V_IO,
pF ¹⁾ V_TxD = V_IO,
7.1.33 CANL/CANH “recessive”
output voltage
7.1.34 CANH, CANL “recessive”
output voltage difference
7.1.35 CANL “dominant” output
voltage
7.1.36 CANH “dominant” output
voltage
7.1.37 CANH, CANL “dominant”
output voltage difference
V_diff = V_CANH - V_CANL
V_CANL/H 2.0
2.5
V_diff
-500 –
V_CANL
0.5 –
V_CANH
2.75 –
V_diff
1.5 –
3.0
50
2.25
4.5
3.0
V no load;
V_TxD = V_IO
mV no load;
V_TxD = V_IO
V V_TxD = 0 V,
50 Ω < R_L < 65 Ω
V V_TxD = 0 V,
50 Ω < R_L < 65 Ω
V V_TxD = 0 V,
50 Ω < R_L < 65 Ω
Data Sheet
16
Rev. 1.0, 2012-03-14