I593 Datasheet, PDF (2/3 Pages) ILSI America LLC – 3.2 mm x 2.5 mm 6 Pads SMD TCXO or TC/VCXO Oscillator

3.2 mm x 2.5 mm 6 Pads SMD TCXO or TC/VCXO Oscillator
Pin Select Funtions
I593 / I793 Series
Voltage Control Function (Pin 1) I793 only
VC Voltage Center & Range
+1.5 V ±1.0 V for both Vcc = +2.5
V & +3.3 V
Frequency Pull Range
±8.0 ppm
Linearity
±1% typ, ±10% max
Transfer Function
Positive
Absolute Voltage
Vcc = +3.3 VDC
+3.63 VDC max
Vcc = +2.5 VDC
+2.63 VDC max
Input Impedance
770 kΩ typ
Harmonics
-5.0 dBc max
E/D Function (Pin 2)
E/D Control
0.7% of Vcc min or no connection enable output
0.3% of Vcc max to disable output (high impedance)
E/D Time
200 nSec max
Disable Time
50 nSec max
SSB Phase Noise
Supply Current
Offset
10 Hz
100 Hz
1 kHz
10 kHz
100 kHz
1 MHz
10 MHz
125.00
-51 dBc/Hz
-83 dBc/Hz
-111 dBc/Hz
-123 dBc/Hz
-125 dBc/Hz
-135 dBc/Hz
-155 dBc/Hz
212.50
-42 dBc/Hz
-87 dBc/Hz
-105 dBc/Hz
-115 dBc/Hz
-118 dBc/Hz
-130 dBc/Hz
-151 dBc/Hz
312.50
-49 dBc/Hz
-88 dBc/Hz
-107 dBc/Hz
-111 dBc/Hz
-114 dBc/Hz
-124 dBc/Hz
-147 dBc/Hz
Current Consumption
Vcc = +2.50 VDC
All values are typical an over
the operating temperature.
Vcc = +3.30 VDC
All values are typical an over
the operating temperature.
LVCMOS
50 MHz = 24mA
125 MHz = 28 mA
200 MHz = 30 mA
50 MHz = 26mA
125 MHz = 30 mA
200 MHz = 34 mA
Table 1
LVPECL
156 MHZ = 36mA
600 MHz = 40mA
800 MHz = 46mA
1.0G Hz = 50mA
156 MHZ = 40mA
600 MHz = 45mA
800 MHz = 48mA
1.0G Hz = 52mA
LVDS
156 MHZ = 22mA
600 MHz = 28mA
800 MHz = 30mA
1.0G Hz = 34mA
156 MHZ = 25mA
600 MHz = 30mA
800 MHz = 32mA
1.0G Hz = 36mA
Tape and Reel Information:
Quantity per
Reel
A
B
C
D
E
F
3000
8.0 ±0.2
4.0 ±0.1
3.5 ±0.05
9.0 ±0.3
60 / 80
180 / 250
ILSI America Phone [phone] ● Fax [phone] ●email: [e-mail] ●
www.ilsiamerica.com
Specifications subject to change without notice
Rev: 03/28/16_D
Page 2 of 3