|
ZLED7010 Datasheet, PDF (1/22 Pages) List of Unclassifed Manufacturers – 40V LED Driver with Temperature Compensation | |||
|
40V LED Driver with
Temperature Compensation
ZLED7010
Datasheet
Brief Description
The ZLED7010, one of our ZLED Family of LED control
ICs, is an inductive step-down converter that is optimal
for driving a single LED or multiple LEDs (connected in
series) from a voltage source greater than the voltage
rating of the LED. The ZLED7010 operates in continu-
ous mode. Capable of operating efficiently with voltage
supplies ranging from 6 VDC to 40 VDC, it is ideal for
low-voltage lighting applications. The ZLED7010 mini-
mizes current consumption by remaining in a low-current
standby mode (output is off) until a voltage of â¥0.3V is
applied to the ADJI pin.
In operating mode, the ZLED7010 can source LEDs with
an output current of ⤠750mA (⤠30 watts of output
power*) that is externally adjustable. The ZLED7010âs
integrated output switch and high-side current sensing
circuit use an external resistor to adjust the average out-
put current. LED control is achieved via an external con-
trol signal at the ZLED7010âs ADJI pin, implemented as
a pulse-width modulation (PWM) waveform for a gated
output current or a DC voltage for continuous current.
The ZLED7010 provides a temperature compen-
sation function for maintaining stable and reliable
LED operation. LED over-temperature conditions
are detected via a negative temperature coefficient
(NTC) thermistor mounted close to the LEDs. If an
over-temperature condition occurs, the NTC value
reaches the value of a threshold resistor and the
IC reduces LED current automatically. After the
circuit recovers to a safe temperature, current
returns to the set value.
ADJO outputs and ADJI inputs of consecutive ICs
can be interconnected as a driver chain deploying
the temperature compensation information of the
predecessor. This reduces the part count because
only the first stage of the series requires an NTC.
6 to 40 VDC
RS
VS
Features
⢠Capable of 95% efficiency*
⢠Operates in continuous mode with a wide input
range from 6 VDC to 40 VDC
⢠Integrated 40V power switch
⢠One-pin on/off or brightness control via DC voltage
or PWM control signal
⢠Switching frequency: ⤠1MHz
⢠Dimming rate: 1200:1 (typical)
⢠Output current accuracy: 5% (typical)
⢠Built-in temperature compensation and open-circuit
protection for LEDs
⢠Thermal shutdown protection for the ZLED7010
⢠Very few external components needed for operation
⢠Broad range of applications: outputs up to â¤750mA
⢠SOP-8 package
Application Examples
⢠Illuminated LED signs and other displays
⢠LED traffic and street lighting (low-voltage)
⢠Architectural LED lighting, including low-voltage
applications for buildings
⢠Halogen replacement LEDs (low-voltage)
⢠LED flood-lighting
⢠LED backlighting
⢠General purpose exterior and interior LED lighting,
including applications requiring low-voltage
⢠General purpose low-voltage industrial applications
ZLED7010 Application Circuit
C1
1μF
C2 R2
100nF 50kΩ
1
D1 2
VIN
4 RNTC
ISENSE
3 RTH ZLED7010 LX 8
6
ADJI
5
GND ADJO
7
n LED
L1
47μH
R3
NTC
* See section 2.3 and 1.4 for details
© 2016 Integrated Device Technology, Inc.
1
April 20, 2016
|
▷ |