IDT72T2098 Datasheet, PDF (1/51 Pages) Integrated Device Technology – 2.5 VOLT HIGH-SPEED TeraSync™ DDR/SDR FIFO 20-BIT/10-BIT CONFIGURATION

2.5 VOLT HIGH-SPEED TeraSync™ DDR/SDR FIFO 20-BIT/10-BIT CONFIGURATION
32,768 x 20/65,536 x 10, 65,536 x 20/131,072 x 10
131,072 x 20/262,144 x 10, 262,144 x 20/524,288 x 10
IDT72T2098, IDT72T20108
IDT72T20118, IDT72T20128
FEATURES:
• Choose among the following memory organizations:
IDT72T2098  32,768 x 20/65,536 x 10
IDT72T20108  65,536 x 20/131,072 x 10
IDT72T20118  131,072 x 20/262,144 x 10
IDT72T20128  262,144 x 20/524,288 x 10
• Up to 250MHz Operation of Clocks
- 4ns read/write cycle time, 3.2ns access time
• Users selectable input port to output port data rates, 500Mb/s
Data Rate
-DDR to DDR
-DDR to SDR
-SDR to DDR
-SDR to SDR
• User selectable HSTL or LVTTL I/Os
• Read Enable & Read Clock Echo outputs aid high speed operation
• 2.5V LVTTL or 1.8V, 1.5V HSTL Port Selectable Input/Ouput voltage
• 3.3V Input tolerant
• Mark & Retransmit, resets read pointer to user marked position
• Write Chip Select (WCS) input enables/disables Write
Operations
• Read Chip Select (RCS) synchronous to RCLK
• Programmable Almost-Empty and Almost-Full flags, each flag
can default to one of four preselected offsets
• Dedicated serial clock input for serial programming of flag offsets
• User selectable input and output port bus sizing
-x20 in to x20 out
-x20 in to x10 out
-x10 in to x20 out
-x10 in to x10 out
• Auto power down minimizes standby power consumption
• Master Reset clears entire FIFO
• Partial Reset clears data, but retains programmable settings
• Empty and Full flags signal FIFO status
• Select IDT Standard timing (using EF and FF flags) or First
Word Fall Through timing (using OR and IR flags)
• Output enable puts data outputs into High-Impedance state
• JTAG port, provided for Boundary Scan function
• 208 Ball Grid array (PBGA), 17mm x 17mm, 1mm pitch
• Easily expandable in depth and width
• Independent Read and Write Clocks (permit reading and writing
simultaneously)
• High-performance submicron CMOS technology
• Industrial temperature range (-40°C to +85°C) is available
FUNCTIONAL BLOCK DIAGRAM
WEN
WCLK
D0 -Dn (x20, x10)
SREN SEN SCLK
WCS WSDR
INPUT REGISTER
OFFSET REGISTER
SI
SO
WRITE CONTROL
LOGIC
WRITE POINTER
RAM ARRAY
32,768 x 20 or 65,536 x 10
65,536 x 20 or 131,072 x 10
131,072 x 20 or 262,144 x 10
262,144 x 20 or 524,288 x 10
FLAG
LOGIC
READ POINTER
FF/IR
PAF
EF/OR
PAE
FWFT
FSEL0
FSEL1
IW
OW
MRS
PRS
TCK
TRST
TMS
TDO
TDI
BUS
CONFIGURATION
RESET
LOGIC
JTAG CONTROL
(BOUNDARY SCAN)
OUTPUT REGISTER
READ
CONTROL
LOGIC
Vref
HSTL
HSTL I/0
CONTROL
OE
Q0 -Qn (x20, x10)
EREN
ERCLK
IDT and the IDT logo are registered trademarks of Integrated Device Technology, Inc. The TeraSync is a trademark of Integrated Device Technology, Inc.
COMMERCIAL AND INDUSTRIAL TEMPERATURE RANGES
1
 2003 Integrated Device Technology, Inc. All rights reserved. Product specifications subject to change without notice.
RT
MARK
RSDR
RCLK
REN
RCS
5996 drw01
DECEMBER 2003
DSC-5996/8