|
F1162NBGI Datasheet, PDF (1/26 Pages) Integrated Device Technology – RF to IF Dual Downconverting Mixer | |||
|
DATASHEET
RF to IF Dual Downconverting Mixer
2300 - 2700 MHz F1162NBGI
GENERAL DESCRIPTION
This document describes the specifications for the
IDTF1162 Zero-DistortionTM RF to IF Downconverting
Mixer. This device is part of a series of mixers offered
with high side or low side injection options for all UTRA
bands. See the Part# Matrix for the details of all devices
in this series.
The F1162 dual channel device is designed to operate
with a single 5V supply. It is optimized for operation in
a Multi-mode, Multi-carrier BaseStation Receiver for RF
bands from 2300 - 2700 MHz with Low Side or High
Side Injection. IF frequencies from 50 to 500 MHz are
supported. Nominally, the device offers +43 dBm
Output IP3 with 330 mA of ICC. Alternately one can
adjust 4 resistor values and a toggle pin to run the
device in low current mode with +38 dBm Output IP3
and 230 mA of ICC.
COMPETITIVE ADVANTAGE
In typical basestation receivers the RF to IF mixer
dominates the linearity performance for the entire
receive system. The Zero-DistortionTM family of mixers
dramatically improve the maximum signal levels (IM3
tones) that the BTS can withstand at a desired Signal to
Noise Ratio (SNR.) Alternately, one can run the device
in Low Current Mode to reduce Power consumption
significantly. Zero-DistortionTM technology allows
realization of either benefit.
IP3O: â 11 dB STD
Mode, â 5 dB LC Mode
Dissipation: â 40% LC,
â 15% STD Mode
Allows for higher RF gain improving Sensitivity
PART# MATRIX
Part#
F1100
F1102
F1150
F1152
F1162
RF freq
range
698 - 915
698 - 915
1700 - 2200
1400 - 2200
2300 â 2700
UTRA bands
5,6,8,12,13,14,17
,19,20
5,6,8,12,13,14,17
,19,20
1,2,3,4,9,10, 33,
34,35, 36, 37,39
1,2,3,4,9,10,111,
211, 241, 33,
34,35, 36, 37,39
7,38,40,41
IF freq
range
50 - 450
50 - 250
50 - 450
50 - 350
50 â 500
Typ.
Gain
8.5
8.5
8.5
8.5
8.9
Injection
High Side
Both
High Side
Low Side
Both
1 â with High side injection
IDT Zero-DistortionTM Mixer
1
FEATURES
⢠Dual Path for Diversity Systems
⢠Ideal for Multi-Carrier Systems
⢠8.9 dB Gain
⢠Ultra linear +43 dBm IP3O
⢠Low NF < 10 dB
⢠200 ⦠output impedance
⢠Ultra high +13 dBm P1dBI
⢠Pin Compatible w/existing solutions
⢠6x6 36 pin package
⢠Constant LO Port Z in STBY mode
⢠< 200 nsec settling from Power Down
⢠Low Current Mode : ICC = 230 mA
⢠Standard Mode: ICC = 330 mA
⢠NOTE production BOM on p. 25
DEVICE BLOCK DIAGRAM
RFIN_A
RF VCO
RFIN_B
IFOUT_A
Bias
Control
STBY
2 LOISET
LCMODE
IFOUT_B
ORDERING INFORMATION
Omit IDT
prefix
0.8 mm height
package
Tape &
Reel
IDTF1162NBGI8
RF product Line
Green
Industrial
Temp range
Rev1, July 2012
|
▷ |