|
9FGL08 Datasheet, PDF (1/19 Pages) Integrated Device Technology – control input polarity | |||
|
8-output 3.3V PCIe Gen 1-2-3 Clock
Generator
9FGL08
Description
The 9FGL0841/51/P1 are members of IDT's 3.3V Low-Power
(LP) PCIe family. The devices have 8 output enables for clock
management and support 2 different spread spectrum levels
in addition to spread off. The 9FGL0841/51/P1 supports both
Common Clock (CC) with or without spread spectrum and
Separate Reference no-Spread (SRnS) PCIe clocking
architectures. The 9FGL08P1 can be programmed with a
user-defined power up default SMBus configuration.
Recommended Application
3.3V PCIe Gen1-2-3 Clock Generator
Output Features
⢠8 â 100 MHz Low-Power HCSL (LP-HCSL) DIF pairs
⢠9FGL0841 default ZOUT = 100ï
⢠9FGL0851 default ZOUT = 85ï
⢠9FGL08P1 factory programmable defaults
⢠1 - 3.3V LVCMOS REF output w/Wake-On-LAN (WOL)
support
Key Specifications
⢠DIF cycle-to-cycle jitter <50ps
⢠DIF output-to-output skew <50ps
⢠DIF phase jitter is PCIe Gen1-2-3 compliant with SSC on or
off
⢠DIF 12k-20M phase jitter is <2ps rms when SSC is off
⢠REF phase jitter is <300fs rms, SSC off, and <1.5ps rms,
SSC is On
⢠±100ppm frequency accuracy on all clocks
Block Diagram
DATASHEET
Features/Benefits
⢠Direct connection to 100ï (xx41) or 85ï (xx51)
transmission lines; saves 32 resistors compared to
standard PCIe devices
⢠130mW typical power consumption; eliminates thermal
concerns
⢠SMBus-selectable features allows optimization to customer
requirements:
⢠control input polarity
⢠control input pull up/downs
⢠slew rate for each output
⢠differential output amplitude
⢠33, 85 or 100⦠output impedance for each output
⢠spread spectrum amount
⢠41 and 51 devices contain default configuration; SMBus
interface not required for device operation
⢠P1 device allows factory programming of customer-defined
SMBus power up default; allows exact optimization to
customer requirements
⢠Outputs can optionally be supplied from any voltage
between 1.05 and 3.3V; maximum power savings
⢠OE# pins; support DIF power management
⢠8MHz â 40MHz input frequency (25MHz default); flexibility
⢠Pin/SMBus selectable 0%, -0.25% or -0.5% spread on DIF
outputs %; minimize EMI and phase jitter for each
application
⢠DIF outputs blocked until PLL is locked; clean system
start-up
⢠Two selectable SMBus addresses; multiple devices can
easily share an SMBus segment
⢠Space saving 48-pin 6x6mm VFQFPN; minimal board
space
vOE(7:0)#
XIN/CLKIN_25
X2
OSC
vSADR
vSS_EN_tri
^CKPWRGD_PD#
SDATA_3.3
SCLK_3.3
CONTROL
LOGIC
SS Capable PLL
REF3.3
DIF7
DIF6
DIF5
DIF4
DIF3
DIF2
DIF1
DIF0
Note: Resistors default to internal on 41/51 devices. P1 devices have programmable default impedances on an output-by-output basis.
9FGL08 REVISION B 07/17/15
1
©2015 Integrated Device Technology, Inc.
|
▷ |