X25057 Datasheet, PDF (8/16 Pages) Xicor Inc. – 5MHz Low Power SPI Serial E 2 PROM with IDLock™ Memory

X25057
ABSOLUTE MAXIMUM RATINGS*
Temperature under Bias ................... –65°C to +135°C
Storage Temperature ....................... –65°C to +150°C
Voltage on any Pin with
Respect to V_SS ................................... –1V to +7V
D.C. Output Current.............................................. 5mA
Lead Temperature
(Soldering, 10 seconds) .............................. 300°C
*COMMENT
Stresses above those listed under “Absolute Maximum
Ratings” may cause permanent damage to the device.
This is a stress rating only and the functional operation of
the device at these or any other conditions above those
indicated in the operational sections of this specification
is not implied. Exposure to absolute maximum rating con-
ditions for extended periods may affect device reliability.
RECOMMENDED OPERATING CONDITIONS
Temperature
Commercial
Industrial
Min.
0°C
–40°C
Max.
+70°C
+85°C
7033 FRM T04
Supply Voltage
X25057
X25057-2.7
X25057-1.8
Limits
4.5V to 5.5V
2.7V to 5.5V
1.8V to 3.6V
7033 FRM T05
D.C. OPERATING CHARACTERISTICS (Over the recommended operating conditions, unless otherwise specified.)
Symbol
Parameter
I_CC1
V_CC Supply Current (Write)
I_CC2
V_CC Supply Current (Read )
I_SB
I_LI
I_LO
V_IL⁽¹⁾
V_IH⁽¹⁾
V_OL1
V_OL2
V_OL3
V_OH1
V_OH2
V_OH3
V_CC Supply Current
(Standby)
Input Leakage Current
Output Leakage Current
Input LOW Voltage
Input HIGH Voltage
Output LOW Voltage
Output LOW Voltage
Output LOW Voltage
Output HIGH Voltage
Output HIGH Voltage
Output HIGH Voltage
POWER-UP TIMING
Limits
Min.
Max.
3
400
1
Units
Test Conditions
mA ^{SCK = V}CC ^{x 0.1/V}CC ^{x 0.9 @ 5MHz, SO =}
Open, CS = V_SS
∝A SCK = V_CC x 0.1/V_CC x 0.9 @ 5MHz, SO =
Open, CS = V_SS
∝A _{CS = VCC, VIN = VSS or VCC}
–0.5
V_CC x 0.7
V_CC – 0.8
V_CC – 0.4
V_CC – 0.2
10
10
V_CC x 0.3
V_CC + 0.5
0.4
0.4
0.4
∝A _{VIN = VSS to VCC}
∝A _{VOUT = VSS to VCC}
V
V
V V_CC > 3.3V, I_OL = 2.1mA
V 2V < V_CC = 3.3V, I _OL = 1mA
V V_CC = 2V, I _OL = 0.5mA
V V_CC > 3.3V, I_OH = -1.0mA
V 2V < VCC = 3.3V, I _OH = -0.4mA
V V_CC = 2V, I _OH = -0.25mA
7033 FRM T06
Symbol
t_PUR⁽²⁾
t_PUW⁽²⁾
Parameter
Power-up to Read Operation
Power-up to Write Operation
Min.
Max.
1
5
Notes: (1)VIL Min. and VIH Max. are for reference only and are not 100% tested.
(2)tPUR and tPUW are the delays required from the time VCC is stable until the specified operation can be initiated. These parameters
are periodically sampled and not 100% tested.
Units
ms
ms
7033 FRM T07
8