IC-MFN Datasheet, PDF (5/13 Pages) IC-Haus GmbH – 8-FOLD FAIL-SAFE N-FET DRIVER

iC-MFN
8-FOLD FAIL-SAFE N-FET DRIVER
Rev A2, Page 5/13
ELECTRICAL CHARACTERISTICS
Operating Conditions: VB = VBR = 4.5. . . 40 V, GND = GNDR = 0 V, Tj = -40...125 °C unless otherwise stated
Item Symbol Parameter
No.
Conditions
Tj Fig.
Unit
°C
Min. Typ. Max.
Total Device
001 VB
Permissible Supply Voltage
4.5
40
V
002 I(VB)
Supply Current in VB
No load, EN5 = lo,EN10 = lo,
ENFS = lo
1.2
3.6 mA
003 I(VB)
Supply Current in VB
004 I(VB)
Supply Current in VB
No load, EN5 = hi,EN10 = lo,
ENFS = lo, IN1. . . 8 = hi,
VB = 8. . . 40 V
No load, EN5 = lo, EN10 = hi,
ENFS = lo, IN1. . . 8 = hi,
VB = 13. . . 40 V
3.2
6.6 mA
3.2
6.8 mA
005 I(VB)
Supply Current in VB
No load, EN5 = lo, EN10 = lo,
ENFS = hi, IN1. . . 8 = hi,
VB = 4.5. . . 40 V
1.3
6.6 mA
006 I(VBR) Supply Current in VBR
tbd
mA
007 I(GND) Current in GND
No load
-7
mA
008 I(GNDR) Current in GNDR
No load, all OUTx = hi
tbd
mA
Current Driver OUT1...8
101 Vc(OUTx)hi Clamp Voltage hi
I() = 10 mA
42
60
V
102 Vc(OUTx)lo Clamp Voltage lo referenced to I() = -10 mA
the lower voltage of GND, GNDR
-2
-0.4
V
103 Vs(OUTx)hi Saturation Voltage hi referenced Vs()hi = VB – V(), INx = hi,
to VB
ENFS = hi;
I() = -0.5 mA
I() = -2 mA
104 Vs(OUTx)lo Saturation Voltage lo referenced I() = 0.5 mA
to GND
I() = 2 mA
105 Vr(OUTx) Output Voltage regulated, no load EN5 = hi, INx = hi,
I() = 0 mA
0.2
V
0.8
V
0.2
V
0.8
V
4.7
5
5.3
V
106 Vr(OUTx) Output Voltage regulated, no load EN10 = hi, INx = hi,
I() = 0 mA
107 Ri(OUTx) Output Resistance
EN10 = hi or EN5 = hi, INx = hi,
I() = ± 2 mA
108 Vl(OUTx) Output Voltage
I(OUTx) = 2 µA, GND open
109 Ipd(OUTx) Pull-Down Current
V(OUTx) = 1 V, GND open
110 Rpd(OUTx) Pull-Down Resistor at OUTx
referenced to GNDR
VB, VBR, V(OUTX) = 10 V, GND
open
111 Rpd(OUTx) Pull-Down Resistor at OUTx
referenced to GNDR
VB, VBR, V(OUTX) = 40 V, GND
open
112 Isc(OUTx)lo Short circuit current lo
V() = 0.8 V...VB
113 Isc(OUTx)hi Short circuit current hi
V() = 0...VB – 0.8 V
114 Vsh(OUTx) Output Voltage at short circuit of EN5 = hi,
two outputs
At two different input signals hi
and lo
115 Vsh(OUTx) Output Voltage at short circuit of EN10 = hi oder ENFS = hi,
two outputs
At two different input signals hi
and lo
116 Vt(OUTx)hi Threshold Voltage hi monitoring Vt() = Vr() – V() or
comparator
Vt() = VB – V()
117 Vt(OUTx)lo Threshold Voltage lo monitoring Vt() = Vr() – V() or
comparator
Vt() = VB – V()
118 Vt()hys Hysteresis
Vt()hys = Vt()lo – Vt()hi
9.4
10 10.6
V
100
500
Ω
600 mV
30
120 µA
50
300 kΩ
100
600 kΩ
2
3.6
10
mA
-10
-3
-2
mA
1
V
1.3
V
0.8
V
2.2
V
50
300 mV