IC-DL Datasheet, PDF (4/9 Pages) IC-Haus GmbH – 3-CHANNEL DIFFERENTIAL LINE DRIVER

iC-DL
3-CHANNEL DIFFERENTIAL LINE DRIVER
Rev B1, Page 4/9
ELECTRICAL CHARACTERISTICS
Operating Conditions: VB1...3 = 4.5...32 V, VCC = 4...5.5 V, Tj = -40...140 °C, unless otherwise noted
input level lo = 0...0.45 V, hi = 2.4 V...VCC, timing diagram see fig. 1
Item Symbol Parameter
No.
Conditions
General (x=1..6)
001 VBx
Supply Voltage Range (Driver)
002 I(VBx)
Supply Current in VB1...3
Ax = lo
003 I(VBx)
Supply Current in VB1...3
Ax = hi
004 I(VBx)
Supply Current in VB1,
Outputs A1...2 Tri-State
ENA = lo,
V(A1...2) = -0.3...(VB + 0.3 V)
005 I(VBx)
Supply Current in VB2...3, Out- ENA = lo,
puts A3...6 Tri-State
V(A3...6) = -0.3...(VB + 0.3 V)
006 IO(Ax)
Output Leakage Current
ENA = lo, V(Ax) = 0 ... VB
007 VCC
Supply Voltage Range (Logic)
008 I(VCC) Supply Current in VCC
ENA = hi, Ax = lo
009 I(VCC) Supply Current in VCC
ENA = hi, Ax = hi
010 Vc()lo
Clamp Voltage low at pins
VB1...3, A1...6, E1...6, DIFF,
ENA TNER, NER, VCC
I() = -10 mA, all other pins open
011 Vc()hi
Clamp Voltage high at Vcc
I() = 10 mA
012 Vc()hi
Clamp Voltage high at pins
VB1...3, A1...6, E1...6, DIFF,
ENA TNER, NER
I() ≤ 2 mA, all other pins open
013 I(VBx)
Supply Current in VB1...3
ENA = hi, f(E1...6) = 1 MHz
Driver Outputs A1...6, Low-Side-action (x = 1...6)
101 Vs(Ax)lo Saturation Voltage low
I(Ax) = 10 mA, Ax = low
102 Vs(Ax)lo Saturation Voltage low
I(Ax) = 30 mA, Ax = low
103 Isc(Ax)lo Short circuit current low
V(Ax) = 1.5 V
104 Isc(Ax)lo Short circuit current low
V(Ax) = VB, Ax = low
105 Rout(Ax) Output resistance
VB = 10...40 V, V(Ax) = 0.5 * VB
106 SR(Ax)lo Slew Rate low
VB = 40 V, Cl(Ax) = 100 pF
107 Vc(Ax)lo Free Wheel Clamp Voltage low I(Ax) = -100 mA
Driver Outputs A1...6, High-Side-action (x = 1...6)
201 Vs(Ax)hi Saturation Voltage high
Vs(Ax)hi = VB - V(Ax),
I(Ax) = -10 mA
202 Vs(Ax)hi Saturation Voltage high
Vs(Ax)hi = VB - V(Ax),
I(Ax) = -30 mA, Ax = hi
203 Isc(Ax)hi Short circuit current high
V(Ax) = VB - 1.5 V, Ax = hi
204 Isc(Ax)hi Short circuit current high
V(Ax) = 0 V, Ax = hi
205 Rout(Ax) Output resistance
VB = 10...40 V, V(Ax) =0.5 * VB
206 SR(Ax)hi Slew Rate high
VB= 40 V, Cl(Ax) = 100 pF
207 Vc(Ax)hi Free Wheel Clamp Voltage high I(Ax) = 100 mA,
VB = VCC = GND
Inputs E1...6, DIFF, ENA, TNER
601 Vt()hi
Threshold Voltage high
602 Vt()lo
Threshold Voltage low
603 Vt()hys Input Hysteresis
Vt()hys = Vt()hi - Vt()lo
604 Ipd()
Pull-Down-Current
V() = 0.8 V
605 Ipd()
Pull-Down-Current
V() ≤ 40 V
Supply Voltage Control VB
701 VBon
Threshold Value at VB1 for Un-
dervoltage Detection on
(NER ⇒ low)
|VB1 - VB2| & |VB2 - VB3| & |VB1 - VB3| <
0.75 V
702 VBoff
Threshold Value at VB1 for Un-
dervoltage Detection off
(NER ⇒ high)
|VB1 - VB2| & |VB2 - VB3| & |VB1 - VB3| <
0.75 V
Min.
4
-20
4
-1.2
5.6
40
40
40
200
-1.3
-90
-800
40
200
0.5
0.8
200
10
3
Typ. Max.
32
1.5
3
1.2
1
20
5.5
5
10
1.5
5
-0.4
7
64
3
10
0.2
0.4
60
90
800
75 100
600
-0.5
0.2
0.4
-60 -40
75 100
400
1.3
2
400 800
80
160
3.95
Unit
V
mA
mA
mA
mA
µA
V
mA
mA
V
V
V
mA
V
V
mA
mA
Ω
V/µs
V
V
V
mA
mA
Ω
V/µs
V
V
V
mV
µA
µA
V
V