15TQ045_17 Datasheet, PDF (1/3 Pages) HY ELECTRONIC CORP. – PHOTOVOLTAIC SOLAR CELL PROTECTION SCHOTTKY RECTIFIER

15TQ045
PHOTOVOLTAIC SOLAR CELL
PROTECTION SCHOTTKY RECTIFIER
FEATURES
●Trench MOS Schottky technology
●Low forward voltage drop,low power losses
●High efficiency operation
●High forward surge capability
●Solder dip 275℃ max. 10s,per JESD 22-B106
●Compliant to RoHS Directive 2002/95/ec and in
accordance to WEEE 2002/96/EC
REVERSE VOLTAGE - 45Volts
FORWARD CURRENT - 15.0 Amperes
R-6
TC measurement point
壳温量测点
MECHANICAL DATA
●Case: JEDEC R-6 molded plastic
●Polarity: Color band denotes cathode
●Weight: 0.07 ounces , 2.1 grams
●Mounting position: Any
Dimensions in inches and (millimeters)
MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS
Rating at 25℃ ambient temperature unless otherwise specified.
Single phase, half wave ,60Hz, resistive or inductive load.
For capacitive load, derate current by 20%
CHARACTERISTICS
SYMBOL
15TQ045
UNIT
Maximum Recurrent Peak Reverse Voltage
Maximum RMS Voltage
Maximum DC Blocking Voltage
Maximum Average Forward (with heatsink)
Rectified Current
(without heatsink, free air)
Peak Forward Surge Current 8.3ms single half sine-wave super
imposed on rated load(JEDEC Method)
IF=5.0A
IF=7.5A TA=25℃
Instantaneous Forward voltage (NOTE 1)
IF=15A
IF=5.0A
IF=7.5A TA=125℃
IF=15A
Reverse Current (NOTE 2)
VR=45V ^TA=25℃
TA=125℃
Typical Junction Capacitance
4.0 V, 1 MHz
Thermal Resistance
Typical Thermal Resistance
Operating Junction Temperature Range
Junction Temperature in DC Forward Current Without reverse bias,
t≤1h (fig. 2) (Note 5)
VRRM
VRMS
VDC
IF(AV)
IF(AV)
IFSM
VF
IR
CJ
RθJA⁽³⁾
RθJL⁽³⁾
RθJL⁽⁴⁾
Top
TJ
0.51 (TYP.)
0.44 (TYP.)
11.6 (TYP.)
7.5 (TYP.)
45
31.5
45
15
6
200
0.44 (TYP.)
0.46 (TYP.)
0.33 (TYP.)
0.36 (TYP.)
1290 (TYP.)
55
3.5
2.5
-40 to +150
≤200
0.59 (MAX.)
0.54 (MAX.)
800 (MAX.)
25 (MAX.)
V
V
V
A
A
V
μA
mA
pF
℃/W
℃/W
℃
℃
Storage Temperature Range
TSTG
-40 to +175
℃
Notes:(1) Pulse test:300 μs pulse width ,1% duty cycle
(2) Pulse test:40ms pulse width
(3) Without heatsink,free air,units mounted on PCB with 2 mm Χ 2 mm copper pad areas at 9.5 mm lead length
(4) Leads clipped at 3 mm lead length from plastic body on 7.0 cm Χ 2.2 cm Χ 1.9 cm Χ 2 heatsink
(5) Meets the requirements of IEC 61215 ed. 2 bypass diode thermal test
(6).The typical data above is for reference only(典型值仅供参考).
Rev. 7, 16-Mar-2017