NVF4-6A Datasheet, PDF (1/1 Pages) HuaXinAn Electronics CO.,LTD – Terminal types as inserting

NVF4-6
34.5 32.5 34
Features
Small size.
Contact load capacity up to 150A.
Suitable for automobile.
Terminal types as inserting.
Ordering Information
NVF4-6 C Z 50 a DC12V N D
1
23 4 5
6
78
1 Part number NVF4-6
2 Contact arrangement A:1A C:1C
3 Enclosure S: Sealed type Z: Dust cover
4 Contact Current 50A,80A,100A,150A
5 Terminals a: plug in type
6 Coil rated voltage(V) DC:12,24
7 Contact material N:AgNi NIL: AgSnO₂
8 Coil transient suppression: D: with diode.;
2D:with two diodes.;.
R: with resistance.;
DR: with diode and resistance;
NIL: standard
Contact Data
Contact Arrangement
Contact Material
Contact Rating (resistive)
Max. Switching Power
Max. Switching Voltage
Contact Resistance or Voltage drop
Operation
life
Electrical
Mechanical
1A SPSTNO ,1C SPDT(B-M)
AgSnO₂ , AgNi
1A
1C
100A,150A/12VDC
50A/24VDC
NO: 50A/24VDC,100A,150A/12VDC
NC: 50A/24VDC,80A,100A/12VDC
1800W
75VDC
Max. Switching Current:150A
30m
Item 4.12 of IEC 61810-7
200mV (at Contact rating)
10⁵
Item 4.30 of IEC 61810-7
10⁷
Item 4.31 of IEC 61810-7
Coil Parameter
Dash
numbers
Coil voltage
VDC
Rated Max.
Coil
resistance
10%
Pickup
voltage
VDC(max)
(65%of rated
voltage )
Release
voltage
VDC(min)
(10% of rated
voltage)
Coil power
consumption
W
Operate
Time
ms
Release
Time
ms
012-2900
12
15.6
50
024-2900
24
31.2
195
7.8
15.6
1.2
2.9
2.4
10
5
CAUTION: 1.The use of any coil voltage less than the rated coil voltage will compromise the operation of the relay.
2.Pickup and release voltage are for test purposes only and are not to be used as design criteria.
143
NVF4-6
Operation condition
Insulation Resistance¹⁾
Dielectric Strength¹⁾
Between contacts
Between contact and coil
100M min (at 500VDC)
50Hz 750V
50Hz 1000V
Item 7 of IEC 61810-5
Item 6 of IEC 61810-5
Item 6 of IEC 61810-5
Shock resistance
Vibration resistance
Terminals strength
Solderability
Ambient Temperature
Relative Humidity
Mass
147m/s² 11ms
10~40Hz double amplitude 1.5mm
30N
235 2 3 0.5s
-40~125
85% (at 40 )
65g
IEC68-2-27 Test Ea
IEC68-2-6 Test Fc
IEC68-2-21 Test Ua2
IEC68-2-20 Test Ta method 1
IEC68-2-3 Test Ca
Note: 1). When testing, coil terminals should be connected ,If coil transient suppression is installed in relay .
Dimensions
mm /inch
34.5max.
1.358max.
32.5max.
1.279max.
35Max.
1.378max.
33Max.
1.300max.
0.8 6.3
0.031 0.248
9.0
0.354
50A
0.8
0.031
9.5
0.374
Dimensions
9
0.354
100A,150A
1.2
0.047
30
85(-)
86(+)
87
30
85(-)
87a
86(+)
85(-)
30
87a
86(+)
87
Wiring diagram (Bottom view)
NOTES 1).Dimensions are in millimeters.
2).Inch equivalents are given for general information only.
0.331
0.661
Mounting (Bottom view)
Ningbo Huaguan Electronics Corporation LTD.
154