HSSR711X Datasheet, PDF (6/12 Pages) Agilent(Hewlett-Packard) – 90 V/1.0 W, Hermetically Sealed, Power MOSFET Optocoupler

6
Typical Characteristics
All typical values are at T_A = 25°C, I_F(ON) = 10 mA, V_F(OFF) = 0.6 V unless otherwise specified.
Parameter
Symbol
Test Conditions
Typ. Units Fig.
Output Off-Capacitance
Output Offset Voltage
Input Diode Temperature
Coefficient
C_O(OFF)
|V_OS|
∆V_F/∆T_A
V_O = 28 V, f = 1 MHz
I_F = 10 mA, I_O = 0 mA
I_F = 10 mA
145 pF
16
2
µV
19
-1.4 mV/C
Input Capacitance
Input-Output Capacitance
Input-Output Resistance
C_IN
V_F = 0 V, f = 1 MHz
C_I-O
V_I-O = 0 V, f = 1 MHz
R_I-O
V_I-O = 500 V, t = 60 s
20
pF
1.5 pF
10¹³
Ω
Turn On Time
With Peaking
t_ON
I_FPK = 100 mA,
0.22
ms
1
I_FSS = 10 mA
V_DD = 28 V, I_O = 800 mA
Notes
7
8
4
4
6
Notes:
1. Maximum junction to case thermal resistance for the device is 15°C/W, where case temperature, T_C, is measured at the center of the
package bottom.
2. For rating, see Figure 4. The output power P_O rating curve is obtained when the part is handling the maximum average output current
I_O as shown in Figure 2.
3. During the pulsed R_ON measurement (I_O duration <30 ms), ambient (T_A) and case temperature (T_C) are equal.
4. Device considered a two terminal device: pins 1 through 4 shorted together and pins 5 through 8 shorted together.
5. This is a momentary withstand test, not an operating condition.
6. For a faster turn-on time, the optional peaking circuit shown in Figure 1 may be implemented.
7. V_OS is a function of I_F, and is defined between pins 5 and 8, with pin 5 as the reference. V_OS must be measured in a stable ambient
(free of temperature gradients).
8. Zero-bias capacitance measured between the LED anode and cathode.
9. Standard parts receive 100% testing at 25°C (Subgroups 1 and 9). SMD and class H parts receive 100% testing at 25°C, 125°C and
-55°C (Subgroups 1 and 9, 2 and 10, 3 and 11 respectively).
CAUTION: Maximum Switching Frequency – Care should be taken during repetitive switching of
loads so as not to exceed the maximum output current, maximum output power dissipation,
maximum case temperature, and maximum junction temperature.
V_CC (+5V)
IN
HSSR-7110
1
8
I_F
+2
7
V_F
–3
6
R2
1200 Ω
R3
4
5
R1
330 Ω
C
15 µF
1/4 54ACTOO
1/4 54ACTOO*
R1 = REQUIRED CURRENT LIMITING RESISTOR
FOR I
F (ON) ^{= 10 mA.}
R2 = PULL-UP RESISTOR FOR V_{F (OFF)} < 600 mV;
IF (V
CC ^{- V}OH^{) < 600 mV, OMIT R2.}
R3, C = OPTIONAL PEAKING CIRCUIT.
* USE SECOND GATE IF I_{F (PK)} > 50 mA
REMINDER: TIE ALL UNUSED INPUTS TO GROUND OR V _CC
TYPICAL VALUES
R3 I_{F (PK)} HSSR-7110
(Ω) (mA)
t_ON (ms)
– _{10 (NO PK)}
2.0
330 ₂₀
1.0
100 ₄₀
0.48
33 ₁₀₀
0.22
Figure 1. Recommended Input Circuit.