HCPL4200 Datasheet, PDF (6/12 Pages) Agilent(Hewlett-Packard) – Optically Coupled 20 mA Current Loop Receiver

Switching Specifications
For 0°C ≤ T_A ≤ 70°C, 4.5 V ≤ V_CC ≤ 20 V, V_E = 0.8 V, all typicals at T_A = 25°C and V_CC = 5 V unless
otherwise noted. See note 13.
Parameter
Symbol Min. Typ. Max. Units Test Conditions Fig. Note
Propagation Delay Time
t_PLH
0.23 1.6 µs V_E = 0 V,
8, 9, 7
to Logic High Output Level
C_L = 15 pF
10
Propagation Delay Time
t_PHL
to Logic Low Output Level
0.17 1.0 µs V_E = 0 V,
C_L = 15 pF
8, 9, 8
10
Propagation Delay Time
t_PLH - t_PHL
60
ns I_I = 20 mA,
8, 9,
Skew
C_L = 15 pF
10
Output Enable Time to
t_PZL
25
ns I_I = 0 mA,
12, 13,
Logic Low Level
C_L = 15 pF
15
Output Enable Time to
t_PZH
Logic High Level
28
ns I_I = 20 mA,
12, 13,
C_L = 15 pF
14
Output Disable Time to
t_PLZ
60
ns I_I = 0 mA,
12, 13,
Logic Low Level
C_L = 15 pF
15
Output Disable Time to
t_PHZ
105
ns I_I = 20 mA,
12, 13,
Logic High Level
C_L = 15 pF
14
Output Rise Time
(10-90%)
t_r
55
ns V_CC = 5 V,
8, 9, 9
C_L = 15 pF
11
Output Fall Time
t_f
15
ns V_CC = 5 V,
8, 9, 1 0
(90-10%)
C_L = 15 pF
11
Common Mode Transient
|CM_H| 1,000 10,000
V/µs V_CM = 50 V (peak) 1 6 1 1
Immunity at Logic High
I_I = 12 mA,
Output Level
T_A = 25°C
Common Mode Transient
Immunity at Logic Low
Output Level
|CM_L| 1,000 10,000
V/µs V_CM = 50 V (peak) 1 6 1 2
I_I = 3 mA,
T_A = 25°C
Package Characteristics
For 0°C ≤ T_A ≤ 70°C, unless otherwise specified. All typicals at T_A = 25°C.
Parameter
Symbol Min. Typ. Max. Units Test Conditions Fig.
Input-Output Momentary V_ISO
Withstand Voltage*
Resistance, Input-Output R_I-O
Capacitance, Input-Output C_I-O
2500
10¹²
1.0
V rms
ohms
pF
RH ≤ 50%, t = 1 min,
T_A = 25°C
V_I-O = 500 V dc
f = 1 MHz, V_I-O = 0 V
Notes
6, 14
6
6
*The Input-Output Momentary Withstand Voltage is a dielectric voltage rating that should not be interpreted as an input-output
continuous voltage rating. For the continuous voltage rating refer to the VDE 0884 Insulation Characteristics Table (if applicable),
your equipment level safety specification, or HP Application Note 1074, “Optocoupler Input-Output Endurance Voltage.”
1-328