SS361RT Datasheet, PDF (1/3 Pages) Honeywell Accelerometers – SOLID STATE SENSOR, IC

FO-55112-C
4
3
HONEYWELL
PART NUMBER
SS361RT
D
HONEYWELL LOGO
2.90
A
3
GROUND
(-)
0.15 C A B
CATALOG LISTING
2.80
1.60
1
VCC (+)
0.20 C
D
NOMINAL
B
PACKAGE
C
HALL ELEMENT
0.95
1.90
DATE CODE
2
OUTPUT
3X
0.50
0.30
0.10
CABD
2
1
REV DOCUMENT
CHANGED BY
CHECK
E 0068435 MH 19AUG10 RS
NOTES
1 - SOLDERING INSTRUCTIONS: EXPOSURE TO HIGH TEMPERATURES SHOULD BE
KEPT AT A MINIMUM HONEYWELL RECOMMENDS AN INFRARED REFLOW
PROCESS WITH PEAK TEMPERATURES NOT EXCEEDING 245
C$
FOR 10 SECONDS MAXIMUM. DO NOT WAVE SOLDER THIS PRODUCT, AS THIS
D
PROCESS MAY NEGATIVELY AFFECT THE SENSOR'S PERFORMANCE AND
RELIABILITY. SUBJECTING THESE PRODUCTS TO WAVE SOLDERING
WILL VOID HONEYWELL'S WARRANTY
2 ABSOLUTE MAXIMUM RATINGS ARE THE EXTREME LIMITS THE DEVICE WILL
MOMENTARILY WITHSTAND WITHOUT DAMAGE TO THE DEVICE. ELECTRICAL AND
MAGNETIC CHARACTERISTICS ARE NOT GUARANTEED IF THE SPECIFIED VOLTAGE
AND/OR CURRENTS ARE EXCEEDED NOR WILL THE DEVICE NECESSARILY OPERATE
AT ABSOLUTE MAXIMUM RATING
3 THE MAGNETIC FLUX USED TO OPERATE THE SWITCH MUST BE IN THE DIRECTION
AND LOCATION SHOWN. (THIS ASSUMES THE CONVENTION THAT THE DIRECTION
OF THE EXTERNAL FLUX OF A MAGNET IS FROM THE NORTH TO THE SOUTH POLE
OF THE MAGNET)
4 THE MAGNETIC FIELD STRENGTH (GAUSS) REQUIRED TO CAUSE THE SWITCH
TO CHANGE STATE (OPERATE AND RELEASE) WILL BE AS SPECIFIED IN THE
MAGNETIC CHARACTERISTICS. TO TEST THE SWITCH AGAINST THE SPECIFIED
MAGNETIC CARACTERISTICS, THE SWITCH MUST BE PLACED IN A UNIFORM
MAGNETIC FIELD
5 THIS PRODUCT WILL BE SUPPLIED IN TAPE AND REEL FORM PER EIA STD 481.
6 GATE VESAGE PERMITTED IN THESE AREAS. UNDERFLUSH BREAKOUT LIMITED
TO .007
7 THESE HALL EFFECT SENSORS MAY HAVE AN INITIAL OUTPUT IN EITHER THE ON
OR OFF STATE IF POWERED UP WITH AN APPLIED MAGNETIC FIELD IN THE
DIFFERENTIAL ZONE (APPLIED MAGNETIC FIELD > Brp AND < Bop). HONEYWELL
C
RECOMMENDS THAT THE APPLICATION CIRCUIT DESIGNER ALLOW 10 MICROSECONDS
AFTER SUPPLY VOLTAGE HAS REACHED 5 VOLTS FOR THE OUTPUT VOLTAGE TO
STABILIZE
S
3
N
6
A SEE DETAIL
B
6
1.45 MAX
1.20
+0.10
-0.30
0.150
0.000
0.10 C
SEATING PLANE
C
C
A
4
3
(0.77) NOMINAL
TO HALL EFFECT
SENSING SURFACE
4 $#4 $
8X 10 $#5 $
0.413
+0.050
-0.150
B
0.787
+0.050
-0.150
(0.60 )
SEATING PLANE
C
A DETAIL
SCALE 40:1
DESIGN UNITS: MM
TOLERANCES UNLESS NOTED:
C
DRAWN
JLH
29 JAN 09
A
CHECK
JLH
29 JAN 09
THIS DRAWING COVERS A PROPRIETARY ITEM
AND IS THE PROPERTY OF HONEYWELL.
THIS DRAWING IS NOT TO BE COPIED OR USED
WITHOUT THE PERMISSION OF HONEYWELL.
TITLE
SOLID STATE SENSOR, IC
INTERPRET PER ASME Y14.5M-1994
OTHER HONEYWELL ENGINEERING
STANDARDS MAY APPLY
SIZE TYPE CAGE_CODE DRAWING NAME
C_{I -}
SS361RT
Pro/ENGINEER
3D ^SCALE NONE
SHEET
REV
E
1 OF 3
2
1