TNC Datasheet, PDF (1/2 Pages) HolyStone International – TANTALUM ELECTROLYTIC CAPACITORS

TANTALUM ELECTROLYTIC CAPACITORS
TNC Series ^{(High Performance Polymer type Chip Tantalum Capacitors)}
Features
• This type reduces ESR by using high performance polymer
based on our original manufacturing process.
• This type is most suitable for an output smoothing circuit that is
used, for example, in a DC-DC converter requring a small size,
large capacitance, and low ESR.
• 260˚C Reflow compatible for Bcace
Product code: (Example) TNC type B case 6.3 V
100 µFʶ20% ESR 45mΩ
TNC B 0J 107 M T R ⁽Z⁾ F
Type of
series
Case size code
Lead-free solder plating
Specific product code
Packing polarity code
With or without taping
Capacitance tolerance code(M : ± 20%)
Capacitance code
Rated voltage code
Outline of drawings and dimensions
Anode indication belt mark
L
˞1MFBTF
TFF
FBDI
QBHF
PG
5.$+
BOE
5.$1
BCPVU
EFUBJMT
JOGPSNBUJPO
PG
+
BOE
1
DBTF
A, B, UB case
Dimensions
(Unit : mm)
Case
code
+
1
"
#
6#
Case size
-
8
)
R
^ʶ ^ʶ ^ʶ ^ʶ
^ʶ ^ʶ ^."9 ^ʶ
^ʶ ^ʶ ^ʶ ^ʶ
^ʶ ^ʶ ^ʶ ^ʶ
^ʶ ^ʶ ^."9 ^ʶ
B
^ʶ
^ʶ
^ʶ
^ʶ
^ʶ
Standard value and case size
Capacitance


Rated voltage (V.DC)




Ж' Code

&

(

+








+ 1








+ 1 "








1 "






+ 1 "

1 "






1 "

"






" #

"






" #

" 6# #






" 6# #

" 6# #






" 6# #

6# #






6# #

#






#

#



#

#
 
#
'PS
SBUJOHT
OPU
DPWFSFE
UIF
UBCMF
DPOTVMU
)JUBDIJ
"*$


"

+ 1

1 "

"

"

"

" 6# #

" 6# #

6# #
Product
specifications
TNC
Operating temperature range –55°C ~ +105°C
Rated voltage DC2.5 ~ 10V
Surge voltage DC3V ~ 13V
Derated voltage DC1.6 ~ 6.3V
Capacitance 3.3 ~ 330µF
Capacitance tolerance ±20%
Test conditions JIS C5101-1:1998
85°C
85°C
(105°C)
120Hz
120Hz
Leakage current _{Refer to standard product table}
—
tanδ
0.1 or less
120Hz
ESR (100kHz)
+ case
1 case
" case
6# case
# case
NЊ^."9
NЊ NЊ^."9
NЊ NЊ^."9
 NЊ^."9
ʙNЊ^."9
100kHz
Maximum permissible
ripple current
(100kHz,20°C)
+ case
1 case
" case
6# case
# case
N"SNT^."9
 N"SNT^."9
 N"SNT^."9 100kHz
 N"SNT^."9
ʙN"SNT^."9
Surge withstanding
voltage
C/C ±20% or less
tanδ Specified initial value or less
LC
ʽ$7
PS
ʽ$7
Charge a surge voltage through a
protective resistor of 33Ω for 30
seconds and discharge it for 5
minutes and 30 seconds at 85°C.
Repeat this operation 1000 times.
4QFDJGJFE
JOJUJBM
WBMVF –

$$
–
ʙˋ ʙˋ
UBOδ


–
7BMVF
TIPXO
UBCMF
Temperature
PS
MFTT
characteristics
Measure the specified
characteristics in each stage.
-$ 3FGFS
UP
—
TUBOEBSE
QSPEVDU
UBCMF
$7
PS
µ"
PS
MFTT
Solder heat
resistance
C/C ±20% or less
tanδ Specified initial value or less
LC
ʽ$7
PS
ʽ$7
Reflow
Board surface peak temperature:
240 ± 5°C
220°C or more: within 30 sec.
Moisture resistance
no load
C/C +30% ~ -20% or less
tanδ Specified initial value or less
LC
300% or less Specified initial value or less
Leave at 40°C and 90 to
95%RH for 500 hours.
High-temperature
load
C/C ±20% or less
tanδ Specified initial value or less
LC
300% or less Specified initial value or less
85°C. The rated voltage is
applied through a protective
resistor of 3Ω for 1000 hours.
Thermal shock
Failure rate
C/C ±20% or less
tanδ Specified initial value or less
LC
ʽ$7
PS
ʽ$7
1% / 1000hrs
Leave at -55°C, normal
temperature, 105°C, and normal
temperature for 30 min., 15 min.,
30 min., and 15 min. Repeat this
operation 5 times running.
85°C. The rated voltage is applied
(through a protective resistor of 1 Ω/V).
˞5IJT
DBUBMPH
JT
EFTJHOFE
GPS
QSPWJEJOH
HFOFSBM
JOGPSNBUJPO
1MFBTF
JORVJSF
PG
PVS
4BMFT
%FQBSUNFOU
UP
DPOGJSN
TQFDJGJDBUJPOT
QSJPS
UP
VTF
131
Hitachi AIC Inc.