HMC862LP3E Datasheet, PDF (1/10 Pages) Hittite Microwave Corporation – 0.1 - 15 GHz LOW NOISE PROGRAMMABLE DIVIDER (N = 1, 2, 4, 8)

HMC862LP3E
v03.1210
0.1 - 15 GHz LOW NOISE PROGRAMMABLE
DIVIDER (N = 1, 2, 4, 8)
Typical Applications
4
The HMC862LP3E is ideal for:
• Satellite Communication Systems
• Point-to-Point & Point-to-Multi-Point Radios
• Military Applications
• Test Equipment
Functional Diagram
Features
Low Noise Floor: -153 dBc/Hz at 100 kHz offset
Programmable Frequency Divider, N = 1, 2, 4, 8
Wide Bandwidth: 100 MHz to 15 GHz
16 Lead 3X3 mm SMT Package: 9mm²
General Description
The HMC862LP3E is a low noise programmable
frequency divider in a 3x3 mm leadless surface
mount package. The divider can be programmed
to divide from N=1, 2, 4, 8 in the 100 MHz to
15 GHz input frequency range. The low phase
noise, wide frequency range and flexible division
ratio make this device ideal for high performance and
wide band communication systems.
4-1
Electrical Specifications, T_A = +25° C, Vcc1 = Vcc2 = +5V
Parameter
Conditions
Min.
Typ.
Max.
Units
RF Input Characteristics
Max RF Input Frequency
Sine Wave or Square Wave Input
15
Min RF Input Frequency
Sine Wave or Square Wave Input ^[1]
RF Input Power Range (N = 1)
Sine Wave or Square Wave Input ^{[1] [2]} Fin < 8 GHz
-10
Sine Wave or Square Wave Input ^{[1] [2]} Fin > 8 GHz
-10
RF Input Power Range (N = 2, 4, 8)
Sine Wave or Square Wave Input ^[1]
-10
GHz
0.1
GHz
10
dBm
0
dBm
10
dBm
Divider Output Characteristics
Output Power (N = 1)
(see the Pout plot for N = 1) ^[2]
-2 to +3
dBm
Output Power (N = 2, 4, 8)
(see the Pout plots for each division ratio)
2
dBm
Divider Ratio N
1, 2, 4, 8
SSB Phase Noise @ 100 kHz Offset
Fin = 6 GHz, Pin = 0 dBm, N = 2
-153
dBc/Hz
Logic Inputs
VIH Input High Voltage
3
5
V
VIL Input Low Voltage
0
0.4
V
Power Supplies
Vcc
Analog Supply
4.75
5
5.25
V
Current Consumption
N = 1, S0 = L, S1 = L, S2 = L
106
mA
N = 2, S0 = H, S1 = L, S2 = L
143
mA
Icc
N = 4, S0 = H, S1 = H, S2 = L
153
mA
N = 8, S0 = H, S1 = H, S2 = H
162
mA
Control Bits
3
Bit
[1] Square wave input waveform is recommended below 400 MHz for best phase noise performance. If sine wave input waveform is used below
400 MHz, it is recommended that power input is > +5 dBm for best operation including phase noise performance.
[2] For N = 1, frequencies > 8 GHz, and input power > 0 dBm, output power will saturate and gradually drop with increasing input power, but
part will continue to function.
For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824
Phone: [phone] Fax: [phone] Order On-line at www.hittite.com
Application Support: Phone: [phone] or [e-mail]