W.FL2_17 Datasheet, PDF (8/8 Pages) Hirose Electric – Ultra-Small Surface Mount Coaxial Connectors - 1.18mm Mated Height

W.FL2 Series●Ultra-Small Surface Mount Coaxial Connectors - 1.18mm Mated Height
■Precautions
1. Plugs
(1) Mating / Unmating
q To disconnect connectors, insert the extraction side of insertion and extraction jig and perform as
described in the diagram below.
• Unmating
*OTFSU
UIF
FYUSBDUJPO
TJEF
PG
UIF

5JMU
UIF
UPPM
BT
TIPXO

: UPPM
VOEFS
UIF
NBUFE
QMVH
BU
UIF
@ BOE
MJGU
UIF
QMVH
DBCMF

DBCMF
DPOOFDUJPO
TJEF
BT
TIPXO 
BTTFNCMZ
3FNPWBM

DPNQMFUFE
●Use of the extraction
tool is absolutely
mandatory. Any attempt
of unmating by pulling
on the cable may result
in damage and affect
the mechanical /
electrical performance.
• Mating
q Align the mating axes of the
plug and the receptacle.
w Confirm that the plug is
positioned to be guided.
(The both axes are aligned and
the plug is positioned stably.)
e Remove the tool by carefully
pulling it up.
:
@
L#;A'"AE"Eaj\
Eaj\e^X`je
.
;
L#;A'"G"HBI"&
>chZgiidgZXZeiVXaZ
=
GZbdkVad[
i]Zidda
(2) P u l l f o r c e s o n t h e
cable after connectors
are mated
L#;A'"AE"
Do not apply any pull forces after the bending
of the cable.
L#;A'"G"HBI"&
'CbVm#
%+'™%)%ineZ
&CbVm#
%('ineZ
(3) Precautions
2. Receptacles
(1) Recommended reflow
temperature profile
Do not twist connectors excessively during mating / unmating.
[ç]
260
240
250 ç max. for
10 seconds
230ç
q The temperature of the printed circuit board
surface temperature at the points of contact
with the terminals.
w Reflow soldering should be performed at a
220
200
180
Preheat
(130 to 180ç)
220ç
printed circuit surface temperature of 250°C
max.
160
e In individual applications the actual
140
120
100
120 seconds max.
50 seconds max.
temperature may vary, depending on the
solder paste type, volume / thickness and
80
60 seconds max.
board size / thickness. Consuly your solder
paste and equipment manufacturer for specific
Time
recommendations.
(2) Recommended metal mask thickness 0.1 mm to 0.12 mm
(3) Reflow cycles
2 times
3. Operating environment and storage conditions
(1) Operating environment
The connectors are not designed to operate in the following environments:
• Exposed to a excessive amounts of fine particles and dust
• Regions and places having a high density of sulfur dioxide, hydrogen sulfide, nitrogen dioxide or other
corrosive gasses.
• Environments having large rapid variations in temperature.
(2) Storage conditions -
Receptacle
Store in the Hirose Electric packaging.
Temperature: -10 to +40ç, Humidity: 85% max.
Use within 6 months of delivery.
Receptacles for which the storage period has elapsed must be tested for solderability to the PC board mounting surface.
Powered by TCPDF (www.tcpdf.org)
8
®
2-6-3,Nakagawa Chuoh,Tsuzuki-Ku,Yokohama-Shi 224-8540,JAPAN
TEL: ^[phone] Fax: ^[phone]
http://www.hirose.com
http://www.hirose-connectors.com
The characteristics and the specifications contained herein are for reference purpose. Please refer to the latest customer drawings prior to use.
The contents of this catalog are current as of date of 11/2014. Contents are subject to change without notice for the purpose of improvements.