W.FL-R-SMT-1_09 Datasheet, PDF (6/6 Pages) Hirose Electric – Ultra Small Surface Mount Coaxial Connectors - 1.4mm Mated Height

The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.
All non-RoH_WS p_.r_Fod_Luc_Sts_eh_ra_ieve_sb_qee_Un _ld_tis_rc_aon_Sti_mnue_ad_l,_lor_Sw_uil_rl _fb_ae_cdi_esc_Mont_oin_uue_nd_ts_Coo_on._aP_xle_ia_ase_l c_Che_oc_nk _nth_ee _cp_tr_ood_ru_scts_–s₁ta_.t₄us_mon_mth_Me H_air_to_es_de w_Heb_es_iit_ge_hRo_tHS search at www.hirose-connectors.com, or contact your Hirose sales representative.
sPrecautions
1. Plug
(1) Mating / unmating
• Unmating
Insert both ends of the extraction tool under the plug (from the direction opposite to the Cable
termination), as shown and pull-up in the direction perpendicular to the mounting surface of the
receptacle.
qRecomended the use of the extraction tool for unmating.
W.FL-LP-N plug extraction tool
Any attempt of unmating by pulling on the cable may result in
damage and affect the mechanical / electrical performance.
W.FL Cable
Assembly
(2) Pull forces on the
cable after connectors
are mated
• Mating Do not attempt to insert on an extreme angle.
W.FL-LP-040
Cable Assembly
After the connectors are mating, do not apply
a load to the cable in excess of the values
indicated in the diagram.
W.FL-R-SMT-1
Receptacle
W.FL-R-SMT-1
∞
2N max
∞
(3) Precautions
Do not twist connectors excessively during mating / unmating.
2. Receptacle
(1) Recommended reflow
temperature profile
[ç]
250 ç max. for
10 seconds
260
240
230ç
220
200
Preheat
180
(130 to 180ç)
220ç
160
140
120
100
120 seconds max.
50 seconds max.
80
60 seconds max.
Time
q The temperature of the printed circuit board surface temperature at the points of contact with the terminals.
w Reflow soldering should be performed at a printed circuit surface temperature of 250°C max.
e In individual applications the actual temperature may vary, depending on the solder paste type, volume / thickness and
board size / thickness. Consuly your solder paste and equipment manufacturer for specific recommendations.
(2) Manual soldering
(3) Recommended metal
mask thickness
(4) Reflow cycles
Soldering iron temperature: 350°C, Soldering time: for 5 seconds max.
0.1 mm to 0.12 mm
2 times
3. Operating environment and storage conditions
(1) Operating environment
The connectors are not designed to operate in the following environments:
• Exposed to a excessive amounts of fine particles and dust
• Regions and places having a high density of sulfur dioxide, hydrogen sulfide, nitrogen dioxide or other corrosive gasses.
• Environments having large rapid variations in temperature.
(2) Storage conditions -
Receptacle
Store in the Hirose Electric packaging.
Temperature: -10 to +40ç, Humidity: 85% max.
Use within 6 months of delivery.
Receptacles for which the storage period has elapsed must be tested for solderability to the PC board mounting surface.
®
5-23,OSAKI 5-CHOME,SHINAGAWA-KU,TOKYO 141-8587,JAPAN
PHONE: [phone], FAX: [phone]
http://www.hirose.com
http://www.hirose-connectors.com
The contents of this catalog are current as of date of 02/2009. Contents are subject to change without notice for the purpose of improvements.
6