|
N-FL Datasheet, PDF (2/6 Pages) Hirose Electric – Lightweight SMT Miniature Coaxial Connectors – 1.4 mm Mated Height | |||
|
◁ |
The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.
All non-RoHNS p.FroLduSctserhiaevse âbeLenigdihsctownteiniugedh, torSwMill TbeMdisicnoinatitnuuerdesoCono.aPlxeaiasel cCheocnk tnheecptroodrusctsâs1ta.t4usmonmtheMHiarotseedweHbseitiegRhotHS search at www.hirose-connectors.com, or contact your Hirose sales representative.
â Specifications
Ratings
Nominal characteristic impedance 50 ohms Operating temperature range -40°C to +90°C (90% RH)
Frequency range
DC to 6 GHz Storage temperature range -30°C to +70°C (90% RH)
Item
Specification
1. Contact resistance
Center contact: 25 m ohms max.
Outer contact: 25 m ohms max.
2. Insulation resistance 500 M ohms min.
3. Withstanding voltage No flashover or insulation breakdown
4. V.S.W.R.(Note)
1.3max.
5. Durability
Contact resistance Center contact: 30 m ohms max.
Outer contact: 30 m ohms max.
No damage, cracks, or parts dislocation
Conditions
10 mA max.
100V DC
200V AC / 1 minute
DC to 6GHz
20 cycles
6. Vibration
No electrical discontinuity of 1 μs or longer
No damage, cracks, or parts dislocation
Frequency: 10 to 100 Hz, single amplitude of 1.5 mm
Acceleration: 59 m/s2, in each of 3 axis
5 cycles
7. Shock
No electrical discontinuity of 1 μs or longer
No damage, cracks, or parts dislocation
Acceleration of 735 m/s2, 11 ms continuous time
Waveform: sine half-wave, 3 cycles in each of the
3 axis
8. Humidity
Insulation resistance: 100 M ohms min. (high humidity)
Insulation resistance: 500 M ohms min. (dry)
No damage, cracks, or parts dislocation
96 hours at +40°C, and humidity of 95%
9. Temperature cycle No damage, cracks, or parts dislocation
Temperature:-40°C/+5°C to +35°C/+90°C/+5°C to +35°C
Time: 30 min./ 5 min. max. / 30 min. / 5 min. max.
5 cycles
10. Salt spray test
No excessive corrosion
5% salt water solution, 48 hours
Note: Information contained in this catalog represents general requirements for this Series. Contact us for the drawings and specifications for a
specific part number shown.
* V.S.W.R. Measurement System
Measured as shown on the block diagram below.
Network Analyzer
Test Set
Test Port
Test Port Cable
D.U.T Termination
Note1: A N.FL Cable assembly (plug) is measured with SMA conversion
adapters mated with N.FL plugs at both ends of a 100cm coaxial cable
harness
Note2: A N.FL receptacle, which is mounted on a 50 ohms glass epoxy board,
is measured with a SMA conversion adapter.
â Materials / Finishes
âPlug
Part
Shell
Female center contact
Insulator
âReceptacle
Part
Shell
Male center contact
Insulator
Material
Phosphor bronze
Phosphor bronze
PBT
Material
Phosphor bronze
Brass
LCP
Finish
Silver plated
Gold plated
Color: Black
Finish
Silver plated
Gold plated
Color: Black
Remarks
-------
-------
UL94V-0
Remarks
-------
-------
UL94V-0
2
|
▷ |