HA5004 Datasheet, PDF (2/8 Pages) Harris Corporation – 100MHz Current Feedback Amplifier

HA-5004
Absolute Maximum Ratings
Supply Voltage (Between V+ and V- Terminals) . . . . . . . . . . . . 40V
Differential Input Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5V
DC Input Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±V_SUPPLY
Output Current . . . . . . . . . . . . . . . ±120mA Max (≤25% Duty Cycle)
Operating Conditions
Thermal Information
Thermal Resistance (Typical, Note 2)
θ_JA (^oC/W) θ_JC (^oC/W)
CERDIP Package. . . . . . . . . . . . . . . . .
75
20
Maximum Junction Temperature (Note 1) . . . . . . . . . . . . . . . 175^oC
Maximum Storage Temperature Range . . . . . . . . . . -65^oC to 150^oC
Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . 300^oC
Temperature Range
HA-5004-5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0^oC to 75^oC
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the
device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
NOTES:
1. Maximum power dissipation, including load condition, must be designed to maintain the junction temperature below 175^oC. See Thermal Resis-
tances in the “Thermal Information” section.
2. θ_JA is measured with the component mounted on an evaluation PC board in free air.
Electrical Specifications
PARAMETER
V_CC = V_C+ = +15V, V_EE = V_C- = -15V, R_S = 50Ω, R_L = 100Ω, A_V = +1, R_F = 250Ω, OE = 0.8V, TOI = 0.8V or
2.0V, Unless Otherwise Specified
TEST CONDITIONS
TEMP. (^oC)
MIN
TYP
MAX
UNITS
INPUT CHARACTERISTICS
Offset Voltage
25
-
1
5
mV
Full
-
-
20
mV
Average Offset Voltage Drift
Bias Current (+Input Only) (Note 3)
Full
-
10
-
µV/^oC
25
-
2
5
µA
Full
-
-
20
µA
Input Resistance (-Input)
Input Resistance (+Input)
Input Capacitance
Common Mode Range
DISTORTION AND NOISE
Total Harmonic Distortion (2V_P-P,
200kHz)
Input Noise Voltage
Input Noise Voltage Density (Note 4)
Input Noise Current Density (Note 4)
DIGITAL I/O CHARACTERISTICS
Logic Inputs (OE and TO)
Logic Output (TOL) (Open Collector)
A_VCL = +1
A_VCL = +2
A_VCL = +5
10Hz to 1MHz
f = 10kHz
f = 100kHz
f = 10kHz
f = 100kHz
V_IH
V_IL
I_IH at V_I = 2.4V
I_IH at V_I = 0.4V
V_OL at 800µA
25
-
6.5
-
Ω
25
-
3
-
MΩ
25
-
3
-
pF
Full
±10
-
-
V
25
-
-72
-
dBc
25
-
-70
-
dBc
25
-
-68
-
dBc
25
-
15
-
µV_P-P
25
-
2.2
-
nV/√Hz
25
-
2.2
-
nV/√Hz
25
-
6
-
pA/√Hz
25
-
4
-
pA/√Hz
Full
2.0
-
-
V
Full
-
-
0.8
V
Full
-
-
1
µA
Full
-
-
10
µA
Full
-
0.05
0.4
V
2