CA3256 Datasheet, PDF (1/11 Pages) Harris Corporation – 25MHz, BiMOS Analog Video Switch and Amplifier

January
Semiconductor
1999
NO
Call
CRoeErnOCetrOBmaSMlaOAiMl:pLEpEcNlTeiDcnEaEtaPtDipoRpRnO@sEDP1hUL-aC8Ar0rTCi0sE-.4cM4o2Em-N7T747
CA3256
25MHz, BiMOS Analog
Video Switch and Amplifier
[ /Title
(CA32
56)
/Sub-
ject
(25MH
z,
BiMO
S Ana-
log
Video
Switch
and
Ampli-
fier)
/Autho
r ()
/Key-
words
(Har-
ris
Semi-
con-
ductor,
4x1,
video
cross-
point
switch,
multi-
plexer
multi-
plexor,
cable
driver,
5x1,
moni
tor out-
put,
adjust-
able
gain,
Features
Description
• 5 Multiplex Video Channels
- 1 Independent Channel
- 4 Channels with Enable
• 4 LED Channel Indicator Outputs
• Wideband Video Amplifier . . . . . . . . 25MHz Unity Gain
• Adjustable Video Amplifier Gain
• High Signal-Drive Capability
Applications
• Video Multiplex Switch
• 75Ω Video Amplifier/Line Driver
• Video Signal-Level Control
• Monitor Switching Control
• TV/CATV Audio/Video Switch
• Video Signal Adder/Fader Control
Part Number Information
PART NUMBER
CA3256E
CA3256M
TEMP.
RANGE (^oC)
PACKAGE
-40 to 85 18 Ld PDIP
-40 to 85 20 Ld SOIC
PKG.
NO.
E18.3
M20.3
The CA3256 BiMOS analog video switch has five channels
of CMOS multiplex switching for general-purpose video-
signal control. One of four CMOS channels may be selected
in parallel with channel 5. The CMOS switches are inputs to
the video amplifier but may be used in bilateral switching
between channels 1 to 4 and channel 5. The analog
switches of channels 1 to 4 are digitally controlled with logic
level conversion and binary decoding to select 1 of 4
channels. The enable function controls channels 1 to 4 but
does not affect channel 5. LED output drivers are selected
with the channel 1-to-4 switch selection to indicate the ON-
channel. Channel 5 may be used as a monitor output for
data or signal information on channels 1 to 4. The
transmission gate switches shown in the block diagram of
the CA3256 are configured in a “T” design to minimize
feedthrough. When the switch is off, the shunt or center of
the “T” is grounded.
The amplifier has high input impedance to minimize the R_ON
transmission gate insertion loss. The amplifier output imped-
ance is typically 5Ω in a complementary symmetry output.
The amplifier can directly drive a nominal 75Ω coaxial cable
to provide line-to-line video switching. The gain of the ampli-
fier is programmable by different feedback resistor values
between pins 8 and 9. Compensation may also be used
between these pins for an optimally flat frequency response.
An internal regulated 5V bias reference with temperature
compensation permits stable direct-coupled output drive and
minimizes DC offset during signal switching.
Pinouts
CA3256
(PDIP)
TOP VIEW
IN 3 1
LED 4 2
IN 4 3
GND 4
V- 5
ENABLE 6
CONTROL C 7
FEEDBACK 8
AMP OUT 9
18 CONTROL B
17 IN 2
16 CONTROL A
15 IN 1
14 V+
13 IN/OUT 5
12 LED 1
11 LED 2
10 LED 3
CA3256
(SOIC)
TOP VIEW
IN3 1
LED4 2
IN4 3
GND 4
V- 5
ENABLE 6
CONTROL C 7
FEEDBACK 8
AMP OUT 9
LED3 10
20 CONTROL B
19 IN2
18 CONTROL A
17 NC
16 IN1
15 V+
14 IN/OUT5
13 NC
12 LED1
11 LED2
CAUTION: These devices are sensitive to electrostatic discharge. Users should follow proper IC Handling Procedures.
Copyright © Harris Corporation 1999
8-1
File Number 1769.5