S12706_15 Datasheet, PDF (8/8 Pages) Hamamatsu Corporation – CMOS linear image sensor

CMOS linear image sensor
S12706
Precautions
(1) Electrostatic countermeasures
This device has a built-in protection circuit against static electrical charges. However, to prevent destroying the device with electro-
static charges, take countermeasures such as grounding yourself, the workbench and tools. Also protect this device from surge volt-
ages which might be caused by peripheral equipment.
(2) Light input window
If dust or dirt gets on the light input window, it will show up as black blemishes on the image. When cleaning, avoid rubbing the
window surface with dry cloth or dry cotton swab, since doing so may generate static electricity. Use soft cloth, paper or a cotton
swab moistened with alcohol to wipe dust and dirt off the window surface. Then blow compressed air onto the window surface so
that no spot or stain remains.
(3) Soldering
To prevent damaging the device during soldering, take precautions to prevent excessive soldering temperatures and times. Solder-
ing should be performed within 5 seconds at a soldering temperature below 260 °C.
(4) Operating and storage environments
Always observe the rated temperature range when handling the device. Operating or storing the device at an excessively high tem-
perature and humidity may cause variations in performance characteristics and must be avoided.
(5) UV light irradiation
This device is not designed to prevent deterioration of characteristics caused by UV exposure, so do not expose it to UV light.
Related information
www.hamamatsu.com/sp/ssd/doc_en.html
Precautions
∙ Notice
∙ Image sensor / Precautions
Information described in this material is current as of January, 2014.
Product specifications are subject to change without prior notice due to improvements or other reasons. This document has been carefully prepared and the
information contained is believed to be accurate. In rare cases, however, there may be inaccuracies such as text errors. Before using these products, always
contact us for the delivery specification sheet to check the latest specifications.
Type numbers of products listed in the delivery specification sheets or supplied as samples may have a suffix "(X)" which means preliminary specifications or
a suffix "(Z)" which means developmental specifications.
The product warranty is valid for one year after delivery and is limited to product repair or replacement for defects discovered and reported to us within that
one year period. However, even if within the warranty period we accept absolutely no liability for any loss caused by natural disasters or improper product
use.
Copying or reprinting the contents described in this material in whole or in part is prohibited without our prior permission.
www.hamamatsu.com
HAMAMATSU PHOTONICS K.K., Solid State Division
1126-1 Ichino-cho, Higashi-ku, Hamamatsu City, 435-8558 Japan, Telephone: [phone], Fax: [phone]
U.S.A.: Hamamatsu Corporation: 360 Foothill Road, Bridgewater, N.J. 08807, U.S.A., Telephone: [phone], Fax: [phone]
Germany: Hamamatsu Photonics Deutschland GmbH: Arzbergerstr. 10, D-82211 Herrsching am Ammersee, Germany, Telephone: [phone], Fax: [phone]
France: Hamamatsu Photonics France S.A.R.L.: 19, Rue du Saule Trapu, Parc du Moulin de Massy, 91882 Massy Cedex, France, Telephone: [phone], Fax: [phone]
United Kingdom: Hamamatsu Photonics UK Limited: 2 Howard Court, 10 Tewin Road, Welwyn Garden City, Hertfordshire AL7 1BW, United Kingdom, Telephone: [phone], Fax: [phone]
North Europe: Hamamatsu Photonics Norden AB: Torshamnsgatan 35 16440 Kista, Sweden, Telephone: [phone], Fax: [phone]
Italy: Hamamatsu Photonics Italia S.r.l.: Strada della Moia, 1 int. 6, 20020 Arese (Milano), Italy, Telephone: [phone], Fax: [phone]
China: Hamamatsu Photonics (China) Co., Ltd.: B1201, Jiaming Center, No.27 Dongsanhuan Beilu, Chaoyang District, Beijing 100020, China, Telephone: [phone], Fax: [phone]
8
Cat. No. KMPD1146E01 Jan. 2014 DN